TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 22

Страница: 22 / 120

Page 22 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

MPU

Series

I/O/M

Manual

Operation

Fiber Optics Communication:

This device contains a fiber optic Ethernet Transceiver

module; any fiber optics device(s) connected to this device through the connecting fiber

optic cable must be suitable for the location in which it is (they are) installed and any

locations where the fiber optic cables are run, with respect to both electrical circuits and

optical radiation, for ATEX and/or IEC Ex installations.

Special Conditions for Safe Use

CAUTION:

To prevent ignition of hazardous atmospheres and to prevent electrical

shock, disconnect from supply circuits before opening, keep tightly closed when circuits

are in operation.

WARNING:

The enclosure contains an internal battery-powered circuit. To prevent

ignition of hazardous atmospheres, do not open enclosure unless area is known to be

non-hazardous. Substitution of components may impair intrinsic safety and op is.

Marking

Equipment

Certificate

Ex d IIB

T4 – T6 IP66

Tamb = -40°C to +70°C

Ultrasonic

DEMKO 05 ATEX

Ultrasonic Transducer

System

DEMKO 09 ATEX 0907098X

IECEx UL 09.0023X

Ex d ia op is IIB T5 Gb

(Um=250v) IP66

Tamb = -40°C to 60°C

Ultrasonic Meter Control

(UCM) w/o display

DEMKO 13 ATEX 1204991X

IECEx UL 13.0019X

Ex d op is IIB T5 Gb IP66

Tamb = -40°C to 60°C

Ultrasonic Meter Control

(UCM) w/o display

Ex d ib IIB T5 Gb IP66

Tamb = -40°C to 60°C

Remote Mounted Display:

Touch Screen Control

Interface (TCI)

Marking

Equipment

Certificate

Ex db op is IIB + H2 T5

Tamb = -50°C to +60°

Aluminum: UMH-H-…

Stainless steel: UMHX-H-…

BVS 17 ATEX E 052 X

IECEx BVS 17.0046X

3.9.1.

Installation of Cables

Due to customer or location specific requirements, the cables for communication and

power supply lines are usually not a part of the delivery. However, the technical speci-

fications for the cables MUST be followed. Prior to the installation, these requirements

must be checked.
The number of and types of cables are dependent on which version or options that are

delivered. A set of wiring diagrams are available covering the different options. Project

specific wiring diagrams may also be available. Cable installation and connection must

be done by professionals with the required skills and certificates.

DO NOT SWITCH POWER ON

until the installation is checked and approved by sup-

plier. Any damage caused by unauthorized operation will void the warranty.

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Бренды по названию

Популярные бренды