TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 25

Страница: 25 / 120

Issue/Rev. 0.1 (11/18) ║ MNKS025 • Page 25

MPU

Series

I/O/M

Manual

Operation

3.11.

Explosion-proof housing closure

When securing the front cover of the UMC, TCI or UMH enclosure, use the following

procedure to ensure the unit is properly sealed and is safe to operate in the hazardous

environment:

1. Inspect the door seal O-ring for damage and replace if damaged. The O-ring is not

required to maintain the explosion-proof rating; however, it is required to maintain the

IP 65 ingress protection rating. Grease cover flange with petroleum jelly or

TechnipFMC grease (P/N 644886401) before attachment of the cover to the housing.

2. Verify the mating areas between the front cover and the main housing are not

scratched, corroded or otherwise damaged such that the surface contact between

them would be compromised.

3. Close the cover and tighten the bolts around the perimeter of the front cover. The final

torque should be 70 IN-LB (8 Nm) for the UMC / TCI enclosure type (pedestal style).

• UMH alternate enclosure type (depicted below) - Once the cover is fitted, ensure

that all the fasteners are present and fully tightened.

• Cover Bolt Torque requirement:

• Aluminum enclosure 20 Nm

• Stainless steel enclosure 25 Nm

(UMH style alternate enclosure)

4. Check that the enclosure is properly sealed by verifying the cover to enclosure joint

“gap” with a 0.0015" (0.038mm) feeler gauge. The feeler gauge must not enter the

joint for more than a ¼" (6mm) at any point around the perimeter of the cover to

housing joint.

3.12.

Flame Path Inspection Criteria

Warning:

To prevent ignition of hazardous atmospheres, disconnect from mains power

supply before opening the cover.

I. Installation/inspection/maintenance/repair/overhaul/reclamation of the MPU in the

European Union must be performed by qualified personnel in accordance with the

applicable requirements of EN 60079-14, EN 60079-17, and EN 60079-19 in addition

to all local codes/regulations.

II. Installation/inspection/maintenance/repair/overhaul/reclamation of AccuLoad’s

relying upon the IECEx certification must be performed by qualified personnel in

accordance with the applicable requirements of IEC 60079-14, IEC 60079-17, and

IEC 60079-19 as required by local codes/regulations.

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды