Supermicro SuperServer 8048B-TRFT, Руководство пользователя

Страница: 38 / 84

Chapter 5: Advanced Serverboard Setup
5-17 5-16
SUPERSERVER 8048B-TRFT USER'S MANUAL
X10QBi Quick Reference
Jumper Description Default Setting
JBT1 Clear CMOS See Section 5-10
JI
2
C1/JI
2
C2 SMB to PCI-E Slots Enable/Disable Pins 2-3 (Disabled)
JPB1 (on I/O module) BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 (on I/O module) VGA Enable/Disable Pins 1-2 (Enabled)
JPME1 ME Mode Recovery Pins 1-2 (Normal)
JPME2 ME Mode Select Pins 1-2 (Normal)
JPL1 (on I/O module) GLAN1/GLAN2 Enable
Pins 1-2 (via con-
nected cable)
JPT1 TPM Enable/Disable Pins 1-2 (Enabled)
JWD1 Watch Dog Pins 1-2 (Reset)
Connector Description
FAN1-FAN10 4-pin System/Cooling Fan Headers
BT2 Onboard Battery
COM1 Serial/COM Part 1 (located on the I/O module)
COM2 Serial/COM Port Header 2
I-SATA 0-5 Intel SATA Ports 0-5
JD1 Speaker/Power LED Indicator
JF1 Front Panel Control Header
JIPMB1 4-pin External BMC I
2
C Header (for an IPMI Card)
JL1 Chassis Intrusion Header
JOH1 Overheat/Fan Fail LED Header
JPI
2
C1 Power Supply SMBbus I
2
C Header
JPW1 ATX 24-pin Power Connector
JPW2-JPW7 8-pin Power Connectors
JSD1 SATA DOM (Device on Module) Power Connector
JVG1/2 VGA/Video Port1/Port2 (located on the I/O module)
LAN1/2 Gb Ethernet Ports 1/2 (located on the I/O module)
LAN3 (on the I/O module) BMC LAN (Dedicated IPMI LAN) (JLAN3)
SP1 Internal Speaker
T-SGPIO 1/2 Serial Link General Purpose I/O Headers
USB0/1, USB2/3, USB6/7 Front Panel Accessible USB Connections
USB4, USB5 Type A Front Panel USB Connectors 4/5
UID UID Switch (SWUID1/SW1) (on the I/O module)
VGA 1/2 VGA Port
5-9 Connector Definitions
DOM Power Connector
A power connector for SATA DOM (Disk-
On-Module) devices is located at JSD1.
Connect the appropriate cable here to
provide power support for your SATA DOM
devices.
DOM PWR
Pin Definitions
Pin# Definition
1 +5V
2 Ground
3 Ground
Warning : To provide adequate power supply to the system, the 24-pin ATX PWR
(JPW1) and all six 8-pin power connectors (JPW2-JPW7) must be connected to the
power supply. Failure to do so will void the manufacturer warranty on your power
supply and serverboard.
Power Connectors
A 24-pin main power supply connector
(JPW1) and six 8-pin power connectors
(JPW2-JPW7) are located on the X10DBi
serverboard. These power connectors
meet the SSI EPS 12V specification.
Connect these power connectors to your
power supply to provide adequate power
to your system. Refer to the table on the
right for pin definitions.
ATX Power 24-pin Connector
Pin Definitions
Pin# Definition Pin # Definition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
12V 8-pin Power
Connector
Pin Definitions
Pins Definition
1 through 4 Ground
5 through 8 +12V
(Required)