Summa S Class 2 OPOS-CAM Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 113

background image

S CLASS™ 2 cutter

User’s Manual

Setup

1-13

1.5

Connecting the cutter to a computer

The S CLASS 2 cutters support bi-directional USB and Ethernet connectivity. When both
ports are connected at the same time, the port that receives the data first will remain active

and the other port will be deactivated.

1.5.1

USB connection

The USB cable should be 5 meters (16 feet) or less in length. The connector on the cutter

side of the cable should be USB series B 4-pin. The connector on the computer side of the
cable should be USB A 4-pin.

1.5.1.1

Connecting the S CLASS 2 cutter to a PC, using a USB cable

NOTE:

When installing a cutter, make sure the user has administrative rights

and UAC is deactivated or set it to its lowest level (not applicable for Windows
XP or earlier versions).

1.

Power-off the cutter.

2.

Insert the S CLASS 2 CD into the computer’s CD-ROM drive.

3.

Choose to run Windows_autostart.

4.

Choose the language and click on install USB driver. Wait for the driver to install.

5.

Connect one end of the USB cable to a USB port on the computer.

6.

Connect the other end of the USB cable to the USB port on the back of the cutter.

7.

Power on the cutter (see section 0) and return to the computer.

The Found New Hardware Wizard should appear on the computer screen and install the
USB driver.

8.

Click “OK” and follow the instructions, provided by the Wizard.

9.

Restart the computer.

NOTE:

When connecting a cutter to a computer for the first time, using the USB

cable, the computer will detect the cutter and install the USB driver if the setup

program was run. If the setup program was not run prior to connection, then

install the program while the cutter is connected and switched on. After the
program is run, the computer will detect a new device and install the correct

driver automatically.

NOTE:

In order to connect more than one cutter to one computer, see the

section on the USB class.

NOTE:

It is recommended to always use the latest version of the driver. The CD

is made this way it downloads the latest version automatically. If no internet
connection is available, then it is possible that the driver on the CD is outdated.

«
...
21
22
23
24
25
...
»

Содержание S Class 2 OPOS-CAM


















































































































Отзывы:

Нет отзывов

Похожие инструкции для S Class 2 OPOS-CAM

Бренд: KEENCUT Страницы: 4

Бренд: Vari Страницы: 18

Бренд: Rockwell Страницы: 20

Бренд: Cub Cadet Страницы: 20

Бренд: The Handy Страницы: 8

Бренд: Logan Graphic Products Страницы: 2

ClassicCut CL100

Бренд: EDNord Страницы: 30

Бренд: ES Страницы: 2

Бренд: Sirman Страницы: 8

TMC24 TURF multi Cutter

Бренд: Groundsman Страницы: 22

Бренд: Poulan Pro Страницы: 9

Бренд: Leigh Страницы: 86

Бренд: YILMAZ Страницы: 21

Бренд: Far Tools Страницы: 42

Бренд: Zenoah Страницы: 16

Бренд: Garten Meister Страницы: 66

Бренд: RASOR Страницы: 16

Бренд: Makita Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды