Summa S Class 2 OPOS-CAM Скачать руководство пользователя страница 18

Страница: 18 / 113

S CLASS™ 2 cutter

User’s Manual

Setup

1-8

Pinch rollers:

The pinch rollers clamp the media to the drive system to ensure accurate

tracking. The S2120(T) has one and the S2160(T) and S2140(T) have two extra pinch

rollers to ensure that wide media stays flat in the middle. The outer drive pinch rollers

have a selectable pressure; the extra rollers in the middle can be enabled or disabled.

Do not move the pinch roller assemblies when holding them from this side.

10.

Screws to secure the cutter base:

Screws (3 left and 3 right) hold the cutter base on its

stand. All the screws must be properly secured before using the cutter.

11.

Tubes for the media basket:

Tubes in the back and front hold the media basket. They

can easily be pulled outwards to put the basket in its place.

12.

Casters:

The casters on the stand are equipped with locking brakes. Once the cutter has

been moved to its new location, press the brakes with your foot to lock the casters.

13.

Media support rollers:

Rotating support rollers for the media roll.

14.

Media basket:

The stand and linen media basket come as standard equipment with all

S CLASS 2 cutters.

Содержание S Class 2 OPOS-CAM


















































































































Результаты поиска

Содержание S Class 2 OPOS-CAM

Отзывы:

Похожие инструкции для S Class 2 OPOS-CAM

Бренды по названию

Популярные бренды

Summa S Class 2 OPOS-CAM, Руководство пользователя

Результаты поиска

Содержание S Class 2 OPOS-CAM

Отзывы:

Похожие инструкции для S Class 2 OPOS-CAM

Бренды по названию

Популярные бренды