Stryker LIFEPAK 20 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 61

Stryker LIFEPAK 20 Скачать руководство пользователя страница 61

3201896-000_B

©2019 Stryker

Page 61 of 61

________________________________________________________________________________

LIFEPAK

®

20

MONITOR/DEFIBRILLATOR

_____________________________________________________________________________

Performance Inspection Procedure (PIP)

For further information, please call Stryker at 1.800.442.1142 or visit www.strykeremergencycare.com

Stryker
11811 Willows Road NE
Redmond, WA 98073-9708 USA
Tel: 425.867.4000
Fax: 425.458.1404
www.strykeremergencycare.com

Stryker Australia Pty Ltd
8 Herbert Street
St Leonards
NSW 2065
Australia

Physio-Control, Inc., 11811 Willows Road NE, Redmond, WA 98052 USA

Stryker European Operations B.V., Herikerbergweg 110, 1101 CM Amsterdam, The Netherlands

_______________________________________________________________________________________________________________________________________________________________________________________
© 2019 Stryker. Specifications are subject to change without notice.

Publication Date: 03/2019

«
...
59
60
61

Содержание LIFEPAK 20






























































Отзывы:

Нет отзывов