Stryker LIFEPAK 20 Скачать руководство пользователя страница 39

Страница: 39 / 61

LIFEPAK

Performance Inspection Procedure (PIP)

3201896-000_B

--- CONTENTS ---

Page 39 of 61

PIP - Standard Paddles Sync Remote Test

Note:

Perform this test if Standard Paddles is used. Otherwise, skip to the next test.

To perform Standard Paddles Sync Remote Test:

1. Establish the setup as shown in Figure 1.25.
2. Turn on the Remote Sync Test Pulse Generator.

Note:

A function generator set to provide a pulse train 5 Vp-p (0-5 V), 5 to

200 ms wide, 120 PPM (2 Hz) can be used alternatively to the Remote
Sync Test Pulse Generator.

3. On the Manual Mode setup page; set the device to Remote Sync

4. Turn the device

OFF

and then turn the device

5. Set the device:

Manual mode

, lead selection to

PADDLES

6. Press the

SYNC

button on the device.

7. On the Sync mode screen, select

REMOTE

8. Verify the SYNC LED is flashing.
9. Charge the device to 200 J.
10. Upon reaching full charge, press the

SHOCK

button to discharge the device.

11. Verify the device displays

"ENERGY DELIVERED"

screen message (for SW-

20 version or below) or switches out of remote sync mode (for SW-26 or
above).

12. On the Manual Mode setup page, set the device to Remote Sync

OFF

13. Turn the device

OFF

Figure 1.25: Standard Paddles Sync

Remote Test Setup

Содержание LIFEPAK 20






























































Результаты поиска

Содержание LIFEPAK 20

Отзывы:

Бренды по названию

Популярные бренды

Stryker LIFEPAK 20, Процедура инспекции

Результаты поиска

Содержание LIFEPAK 20

Отзывы:

Бренды по названию

Популярные бренды