Stryker LIFEPAK 20 Скачать руководство пользователя страница 26

Страница: 26 / 61

LIFEPAK

Performance Inspection Procedure (PIP)

3201896-000_B

--- CONTENTS ---

Page 26 of 61

PIP - QUIK-COMBO Defibrillator Sync Test at 2J

To perform QUIK- COMBO Defibrillator Sync Test at 2J:

Note:

Perform this test if Quik-Combo cable is used. Otherwise, skip to the next test

To perform Quik-Combo Defibrillator Sync Test at 2 J:

1. Establish the setup as shown in Figure 1.15.

Note:

Ensure proper test setup connections to the Defibrillator Analyzer. To avoid

damage to the Analyzer or defibrillator, do NOT apply defibrillator pulses to the pacer
inputs of the analyzer.

2. Turn the device

ON.

3. Set the device:

Manual

mode,

ECG Size

to 1.0,

LEAD

selection to

Lead II

4. Set the Defibrillator Analyzer to measure

SYNC

5. Press the

SYNC

button

and select

LOCAL

, if Remote Sync is set to on.

6. Verify the Sync LED turns on and R-wave markers appear on the ECG waveform.
7. Press the

ENERGY SELECT

button to select 2J.

8. Press the

CHARGE

button and wait for the device to reach full charge. Then push

the

SHOCK

button to discharge the device.

9. Verify the defibrillator analyzer measures a sync R-wave is within 1.0 ms to 60ms.
10. Continue to the next test with this setup in place

Figure 1.15: Quik-Combo

Defibrillator Delivered Energy Setup

Содержание LIFEPAK 20






























































Результаты поиска

Содержание LIFEPAK 20

Отзывы:

Бренды по названию

Популярные бренды

Stryker LIFEPAK 20, Процедура инспекции

Результаты поиска

Содержание LIFEPAK 20

Отзывы:

Бренды по названию

Популярные бренды