Stryker LIFEPAK 20 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 61

Stryker LIFEPAK 20 Скачать руководство пользователя страница 36

LIFEPAK

®

20

Performance Inspection Procedure (PIP)

3201896-000_B

©2019 Stryker

--- CONTENTS ---

Page 36 of 61

PIP - Standard Paddles Defibrillator Delivered Energy and Charge Time Tests at 360J (Battery Powered)

WARNING

SHOCK HAZARD

Electrical energy is discharged during this procedure. Do not allow the electrodes to contact any person or conductive surface
except as described below.

To perform Standard Paddles Defibrillator Delivered Energy and Charge Time Tests at 360J (Battery Powered)

1. Establish the setup as shown in Figure 1.22.
2. Disconnect the AC power cable from the device and turn the

device

ON

by battery.

3. Press the

ENERGY SELECT

button to select 360 J.

4. Start a Stop Watch, then press the

CHARGE

button on Standard

Paddles and wait for the device to reach full charge. Stop a Stop Watch,
and then push both

SHOCK

buttons on Standard Paddles to discharge

the device.

5. Verify the defibrillator analyzer indicates the delivered energy is within

306.0 J to 414.0 J.

6. Verify the Charge Time is within 1s to 10 s.

Note:

Perform the TCP- Defibrillator Energy Calibration if the delivered

energy falls outside of the acceptable output range.

7. After testing is complete reconnect the AC power cable to the device.

Figure 1.22: Standard Paddles Defibrillator

Energy and Charge Time Test Setup

«
...
34
35
36
37
38
...
»

Содержание LIFEPAK 20






























































Отзывы:

Нет отзывов