Stryker LIFEPAK 20 Скачать руководство пользователя страница 20

Страница: 20 / 61

LIFEPAK

Performance Inspection Procedure (PIP)

3201896-000_B

--- CONTENTS ---

Page 20 of 61

PIP - 3-Lead ECG Tests

Note:

Perform this test if 3-lead ECG cable is used. Otherwise, skip to the next test.

The 3-Lead ECG tests consist of:

PIP - 3-Lead ECG Leads Off Detection Test

PIP - 3-Lead ECG Gain Test

PIP - 3-Lead ECG Leads Off Detection Test

Connect the 3-Lead ECG cable between the device and Impulse 7000DP as

shown in Figure 1.10.

Set the Impulse 7000DP output to a 1-mv, 10-Hz sine wave.

Set the device

LEAD

selection to

Lead II

Remove the

LA lead

from the Impulse 7000DP, and verify the device displays

the

ECG LEADS OFF

message and a repeating priority 3 tone shall sound when

the Lead is removed. Reconnect the LA lead.

Remove the

RA lead

from the Impulse 7000DP, and verify the device displays

the

RA LEADS OFF

message and a repeating priority 3 tone shall sound when

the Lead is removed. Reconnect the RA lead.

Remove the

LL lead

from the Impulse 7000DP, and verify the device displays

the

LL LEADS OFF

message and a repeating priority 3 tone shall sound when

the Lead is removed. Reconnect the LL lead.

Continue with the next test with this setup in place.

Figure 1.10: 3 Lead ECG Leads Test Setup

Содержание LIFEPAK 20






























































Результаты поиска

Содержание LIFEPAK 20

Отзывы:

Похожие инструкции для LIFEPAK 20

Бренды по названию

Популярные бренды

Stryker LIFEPAK 20, Процедура инспекции

Результаты поиска

Содержание LIFEPAK 20

Отзывы:

Похожие инструкции для LIFEPAK 20

Бренды по названию

Популярные бренды