manualshive.com logo in svg

STMicroelectronics STM32F405, Справочное руководство


Поделиться
Скачать
background image

DocID018909 Rev 11

835/1731

RM0090

Inter-integrated circuit (I

2

C) interface

864

Figure 241. Transfer sequence diagram for slave transmitter

1. The EV1 and EV3_1 events stretch SCL low until the end of the corresponding software sequence.
2. The EV3 event stretches SCL low if the software sequence is not completed before the end of the next byte 

transmission

Slave receiver

Following the address reception and after clearing ADDR, the slave receives bytes from the 
SDA line into the DR register via the internal shift register. After each byte the interface 
generates in sequence:

•

An acknowledge pulse if the ACK bit is set

•

The RxNE bit is set by hardware and an interrupt is generated if the ITEVFEN and 
ITBUFEN bit is set.

If RxNE is set and the data in the DR register is not read before the end of the next data 
reception, the BTF bit is set and the interface waits until BTF is cleared by a read from the 
I2C_DR register, stretching SCL low (see 

Figure 242

 Transfer sequencing).

7-bit slave transmitter

10-bit slave transmitter

Legend: 

S

= 

S

t

a

rt, 

S

r 

= Repe

a

ted 

S

t

a

rt, P= 

S

top, A= Acknowledge, NA= Non-

a

cknowledge,

EVx= Event (with interr

u

pt if ITEVFEN=1)

EV1:

 ADDR=1, cle

a

red by re

a

ding 

S

R1 followed by re

a

ding 

S

R2

EV3-1: 

TxE=1, 

s

hift regi

s

ter empty, d

a

t

a

 regi

s

ter empty, write D

a

t

a

1 in DR.

EV3: 

TxE=1, 

s

hift regi

s

ter not empty, d

a

t

a

 regi

s

ter empty, cle

a

red by writing DR

 

EV3-2: 

AF=1; AF i

s

 cle

a

red by writing ‘0’ in AF bit of 

S

R1 regi

s

ter.

S

Addre

ss

A

D

a

t

a

1

A

D

a

t

a

2

A

.....

D

a

t

a

N

NA

P

EV1 EV

3

-1 EV

3

EV

3

EV

3

EV

3

-2

S

He

a

der

A

Addre

ss

A

EV1

S

r

He

a

der

A

D

a

t

a

1

A

.... D

a

t

a

N

NA P

EV1 EV

3

_1

EV

3

EV

3

EV

3

-2

a

i1

8

209

Содержание STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для STM32F405

unicore UM960 Installation And Operation User Manual preview
UM960
Бренд: unicore Страницы: 25
unicore UM960L Installation And Operation User Manual preview
UM960L
Бренд: unicore Страницы: 24
Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Бренд: Fairchild Страницы: 2
Fagor 101 Operating Manual preview
101
Бренд: Fagor Страницы: 103
Wave Italy IMPACT Installation, Use And Maintenance Manual preview
IMPACT
Бренд: Wave Italy Страницы: 16
TA Hydronics STS Technical Description preview
STS
Бренд: TA Hydronics Страницы: 14
Yudian AI Series Operation Instruction Manual preview
AI Series
Бренд: Yudian Страницы: 26
Eaton COOPER POWER SERIES Installation And Operation Instruction Manual preview
COOPER POWER SERIES
Бренд: Eaton Страницы: 50
IFM CR710S Original Operating Instructions preview
CR710S
Бренд: IFM Страницы: 49
UNICORECOMM UM4B0 User Manual preview
UM4B0
Бренд: UNICORECOMM Страницы: 32
UNICORECOMM UM220-IV M0 Additional Instructions For Installation And Operation preview
UM220-IV M0
Бренд: UNICORECOMM Страницы: 7
UNICORECOMM UM220-INS NF Installation And Operation User Manual preview
UM220-INS NF
Бренд: UNICORECOMM Страницы: 26
UNICORECOMM UM220-INS NF User Manual preview
UM220-INS NF
Бренд: UNICORECOMM Страницы: 25
Watts FEBCO 860 Small Series Installation Maintenance Repair Manual preview
FEBCO 860 Small Series
Бренд: Watts Страницы: 12
Bardiani Valvole BBZS5 Instruction, Use And Maintenance Manual preview
BBZS5
Бренд: Bardiani Valvole Страницы: 54
Parker 890CS Product Manual preview
890CS
Бренд: Parker Страницы: 478
Linear Technology LT8570 Demo Manual preview
LT8570
Бренд: Linear Technology Страницы: 7
YASKAWA J1000 CIMR-JC series Installation Manual preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды