manualshive.com logo in svg

STMicroelectronics STM32F405, Справочное руководство


Поделиться
Скачать
background image

Serial peripheral interface (SPI)

RM0090

868/1731

DocID018909 Rev 11

28.3 

SPI functional description

28.3.1 General 

description

The block diagram of the SPI is shown in 

Figure 246

. 

Figure 246. SPI block diagram

Usually, the SPI is connected to external devices through 4 pins:

•

MISO: Master In / Slave Out data. This pin can be used to transmit data in slave mode 
and receive data in master mode.

•

MOSI: Master Out / Slave In data. This pin can be used to transmit data in master 
mode and receive data in slave mode.

•

SCK: Serial Clock output for SPI masters and input for SPI slaves.

•

NSS: Slave select. This is an optional pin to select a slave device. This pin acts as a 
‘chip select’ to let the SPI master communicate with slaves individually and to avoid 
contention on the data lines. Slave NSS inputs can be driven by standard IO ports on 
the master device. The NSS pin may also be used as an output if enabled (SSOE bit) 
and driven low if the SPI is in master configuration. In this manner, all NSS pins from 
devices connected to the Master NSS pin see a low level and become slaves when 
they are configured in NSS hardware mode. When configured in master mode with 
NSS configured as an input (MSTR=1 and SSOE=0) and if NSS is pulled low, the SPI 
enters the master mode fault state: the MSTR bit is automatically cleared and the 

-/3)

-)3/

"AUDRATEGENERATOR

3#+

-ASTERCONTROLLOGIC

#OMMUNICATION

CONTROL

30% "2

"2 "2

-342 #0/, #0(!

"2;=

28.%

,3"

")$)

-/$%

")$)

/%

33- 33)

"39

/62

-/$

28.%

48%

%22

48%

$&&

33/%

#2#
%.

28
/.,9

#2#
.EXT

#2#

%22

.33

)%

&

&)234

30)?#2

30)?#2

30)?32

48$-

!%.

28$-

!%.

)%

)%

!DDRESSANDDATABUS

2EAD

2XBUFFER

3HIFTREGISTER

,3"FIRST

4XBUFFER

7RITE

AI

Содержание STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для STM32F405

Ebyte E70 Series User Manual preview
E70 Series
Бренд: Ebyte Страницы: 34
XVision XD200 User Manual preview
XD200
Бренд: XVision Страницы: 28
YASKAWA CC-Link Installation Manual preview
CC-Link
Бренд: YASKAWA Страницы: 61
Saluki SMR Series Quick Start Manual preview
SMR Series
Бренд: Saluki Страницы: 13
J+J J4C S20 Quick Start Manual preview
J4C S20
Бренд: J+J Страницы: 4
Val Controls I 24-AF Series Replacement Manual preview
I 24-AF Series
Бренд: Val Controls Страницы: 6
YOKOGAWA UTAdvanced UT35A Technical Information preview
UTAdvanced UT35A
Бренд: YOKOGAWA Страницы: 18
Yale Real Living iM1 Installation And Programming Instructions preview
Real Living iM1
Бренд: Yale Страницы: 2
TeleMann DTR5000N Manual preview
DTR5000N
Бренд: TeleMann Страницы: 4
Water Worker WWDPC Installation Manual preview
WWDPC
Бренд: Water Worker Страницы: 8
YASKAWA A1000 HHP Programming Manual preview
A1000 HHP
Бренд: YASKAWA Страницы: 360
U-Tron 6830-122-C10 Instruction Manual preview
6830-122-C10
Бренд: U-Tron Страницы: 8
Agilent Technologies G8600-68001 Field Installation Instructions preview
G8600-68001
Бренд: Agilent Technologies Страницы: 20
P.W. KEY rt-208gt Operating Manual preview
rt-208gt
Бренд: P.W. KEY Страницы: 20
Vageo RT-1 Manual preview
RT-1
Бренд: Vageo Страницы: 2
DirectConnect VC70DSW Instructions preview
VC70DSW
Бренд: DirectConnect Страницы: 2
pizzato CS ME-02 Series Manual preview
CS ME-02 Series
Бренд: pizzato Страницы: 12
Vag GA INSTRUMENTS K-1255 Installation, Operation And Maintenance Manual preview
GA INSTRUMENTS K-1255
Бренд: Vag Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды