Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 68

Страница: 68 / 94

Event message

Description

Type

PV current too high

The input current at the inverter exceeds the

permissible value. The inverter limits the current to

the permissible value.

Contact your installer if this alarm occurs

frequently.

PV voltage too high

The input voltage applied on the inverter exceeds

the permissible value.

Switch off the DC load-break switch of the

inverter and notify your installer.

Reading CountryCode

failed

The inverter could not correctly read out the

country setting from the memory.

Notify your installer.

Residual current too high

The fault current that flows from the plus or minus

input via the PV generators exceeds the permissible

value. Pursuant to statutory regulations, the

inverter switches off automatically as long as this

fault is pending.

Notify your installer.

RS485 Gateway activated

No communication with the inverter possible via

the RS485 interface.

Disconnect the inverter from the grid and reset it

(AC reset).

Have your installer carry out this operation.

Self test failed

An error occurred during the self-test, the self-test

has been aborted.

Notify your installer if

the self-test has been aborted repeatedly at

different times a day due to an error and

grid voltage and frequency were definitely within

the limit values of the country setting.

Software incompatible

"After a firmware update, the different software

statuses in the inverter do not match any more.

1. Repeat the firmware update using a valid update

file.

2. Contact your installer if this error occurs

frequently.

Time/date lost

The inverter lost the time because it remained

unconnected from the grid for too long a time.

Yield data cannot be stored, event messages only

with incorrect date.

Correct the time settings under

Settings

Time/date

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды