Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 18

Страница: 18 / 94

Max. daily yield

: The maximum daily yield achieved

Operating hours

: The operating hours during which the

device has been connected to the grid (including night-time

hours).

Total yield

: Yield since commissioning

savings

: CO

savings achieved since commissioning

Measurement is always displayed (cannot be switched off)

Possible causes:

–

Internal temperature too high

–

User default Power limiter

–

Frequency too high

–

Controlled by grid operator (feed-in management)

–

Delayed increase in power after starting

Can be reset to 0 via

Settings

▶

Reset max. vals.

An acoustic alarm sounds (approx. 4.5 kHz) when an event message

is displayed.

2 Sounds: Warning

3 Sounds: Error

The acoustic alarm is switched off with the factory default settings.

off

automatic

: Switches on for 30 seconds when a button is

pushed

Grid feed:

(factory setting)

–

Not feeding: Switches on for 30 seconds when a button is

pushed; then switches off

–

Feeding: Switches on for 30 seconds when a button is

pushed; then dims

Notice
–

A prerequisite for this is that you know the

parameters required for setting up the TCP/IP

network connection. Consult (further) technical

professionals if required.

–

DHCP is activated in the device ex-works. This

allows automatic integration of the device in

most networks.

Network settings, required for network communication, e. g. with an

Internet portal:

DHCP

: Switch DHCP on/off

IP address

: IP address of the inverter

Subnet mask

: Subnet mask of the inverter

Gateway

: IP address of the network gateway

Acoustic alarm

Backlight

TCP/IP network

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды