Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 31

Страница: 31 / 94

Installation

4.1 Safety measures during installation

Observe the following safety notes when performing the work

described in Section Installation .

DANGER!
Risk of death by electrocution!
–

Only technical professionals may perform the

work described in Section Installation .

–

Do not connect cables to the inverter until

explicitly asked to do so in the manual.

–

Do not open the housing of the inverter.

–

Connect only SELV circuits to the RJ45 sockets.

–

Lay the cables such that the connection cannot

come loose accidentally.

–

When laying cables, ensure that no damage

occurs to any of the constructional fire safety

measures in the building.

–

Make sure that no inflammable gases are

present.

–

Observe all applicable installation regulations

and standards, national laws and connection

values specified by the regional power supply

company.

DANGER!
Danger from electrical current
ELECTRICAL SHOCK AND DISCHARGE!

The PV generators/lines may be energised as soon as

the PV generators are exposed to light.

Always disconnect all DC and AC cables as follows before starting

work on the inverter:

Turn the AC circuit breaker to off. Take measures to prevent

the system from being unintentionally switched on again.

Set the DC circuit breaker on the inverter to position

. Take

measures to prevent the system from being unintentionally

switched on again.

Disconnect the DC cable plug connectors according to the

manufacturer's instructions.

Disconnecting the AC plug from the inverter

⇒

Release safety

clip at the front of the AC plug by depressing it with a

suitable object, then pull the plug out.

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды