Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 48

Страница: 48 / 94

Disconnect the DC cable plug connectors according to the

manufacturer's instructions; see appendix.

WARNING!
DC cables carry voltage when the PV generators are

subjected to sunlight.

Disconnecting the AC plug from the inverter

Release the safety clip at the front of the AC plug by

depressing it with a suitable object, then pull the plug out.

Check that all pins of the AC plug are free of voltage:

Use a suitable voltmeter for this (do not use a simple neon

phase checker).

Opening the AC plug:

First, unscrew the rear cable connection. Next, release the

safety clips at the left and right of the plug housing by

depressing them simultaneously with a suitable object. Now,

pull the top part of the housing off the contact element.

Use one hand to press the retaining plate on the mounting

plate approx. 5 mm towards the mounting surface

①

(Fig.

left).

Use the other hand to push the inverter upwards, far enough

so that the retaining plate no longer latches

②

. Release the

retaining plate.

Lift the inverter with both hands until the hooks on the rear

side of the inverter are free

③

Remove the inverter from the mounting surface

④

Disconnecting the DC

connections from the

inverter

Disconnecting the AC

plug from the inverter

Opening the AC plug

(only if required)

Removing the inverter

from the mounting

surface

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды