ENGLISH
41
41
es
gb
it
gr
11.4.3.3 Cutting (Fig. 31)
The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the cord parallel
to the ground when cutting. Avoid pressing the trimmer
head against the ground as this can ruin the lawn and
damage the tool.
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting. Constant
contact of this type can cause damage and wear to the
trimmer head.
11.4.3.4 Sweeping (Fig. 32)
The fan effect of the rotating cord can be used for quick
and easy clearing up. Hold the cord parallel to and above
the area to be swept and move the tool to and fro.
When cutting and sweeping you should use full throttle to
obtain the best results.
11.4.4 Trimming branch or leaves with Long-
reach hedge trimmer
- Work with a swinging action from the bottom upwards
when trimming sides. (Fig. 33).
- Always work at full throttle. (Fig. 34).
- When trimming a hedge the engine should always face
away from the hedge. (Fig. 34).
- Hold the machine as close to your body as possible to
get the best balance. (Fig. 34).
- Make sure that the tip does not touch the ground. (Fig.
34).
- Do not rush the work, but work steadily until all the
branches have been cut back cleanly. (Fig. 34).
The following ranges are for normal operating conditions
only. If the working day is longer or if the operating
conditions are difficult (for example very dusty
environments), reduce the specified intervals accordingly
Before starting work
At the end of the work
After each refueling
Every week
Every month
Every 12 months
In case of problems
In case of damage
As needed
All the appliance
Visual inspection (condition, wear, leaks)
*
*
Clean
*
Handle
Verify operation
*
*
Air filter
Clean
*
*
*
Replace
*
*
Fuel tank filter
Check
*
Replace the filter
*
*
*
Carburetor.
Check the minimum setting
*
*
Check the minimum
*
Candle.
Record the distance between the electrodes
*
Replace after 100 hours of operation
Ventilation openings
Clean
*
Adapter
Fill with grease
*
Saw chain
Check
*
Sharpen or replace
*
*
Guide bar
Check
*
Sharpen or replace
*
*
Lama.
Check
*
Sharpen or replace
*
*
All screws accessible
Check
*
Tighten again
*
Anti-vibration elements
Check
*
*
*
Replace
*
Safety labels
Replace
*
Muffler
Clean
*
12.
MAINTENANCE TIMESCALE
Содержание MULTI GAS CUTTER B
