manualshive.com logo in svg

Silicon Laboratories Si5342, Справочное руководство для семьи


Поделиться
Скачать
background image

Si5345-44-42-D-RM

32

Rev. 1.0

5.4.  Interrupt Configuration

There is an interrupt pin available on the device which is used to indicate a change in state of one or several of the
status indicators. Any of the status indicators are maskable to prevent assertion of the interrupt pin. The state of the
INTR pin is reset by clearing the status register that caused the interrupt. If an interrupt occurs the various status
registers from the unmasked flags must be checked and then cleared.

Figure 15. Interrupt Pin Source Masking Options

Th

e _FLG bits are “sticky” versions of the alarm bits and will stay high until cleared. An _FLG bit can be cleared by

writing a zero to the _FLG bit.   When an _FLG bit is high and its corresponding alarm bit is low, the _FLG bit can
be cleared.

During run time, the source of an interrupt can be determined by reading the _FLG register values and logically
ANDing them with the corresponding _MSK register bits (after inverting the _MSK bit values). If the result is a logic
one, then the _FLG bit will cause an interrupt.

For example, if LOS_FLG[0] is high and LOS_INTR_MSK[0] is low, then the INTR pin will be active (low) and
cause an interrupt. If LOS[0] is zero and LOS_MSK[0] is one, writing a zero to LOS_MSK[0] will clear the interrupt
(assuming that there are no other interrupt sources). If LOS[0] is high, then LOS_FLG[0] and the interrupt cannot
be cleared.

INTRb

LOL_INTR_MSK

OOF_INTR_MSK[3-0]

LOS_INTR_MSK[3-0]

&$/B)/*

HOLD_INTR_MSK

/26;$;%B)/*

LOSXAXB_INTR_MSK

22)B)/*>@

/26B)/*>@

+2/'B)/*

CAL_INTR_MSK

/2/B)/*

/265()B)/*

LOSREF_INTR_MSK

;$;%B(55B)/*

XAXB_ERR_INTR_MSK

60%B70287B)/*

SMB_TMOUT_INTR_MSK

6<6,1&$/B)/*

SYSINCAL_INTR_MSK

Содержание Si5342































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Si5342

Sangoma A400 Installation Manual preview
A400
Бренд: Sangoma Страницы: 6
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Бренд: ekwb Страницы: 2
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Бренд: N.A.T. Страницы: 32
Keithley PDISO-8 User Manual preview
PDISO-8
Бренд: Keithley Страницы: 71
XtendLan NVR-xUD User Manual preview
NVR-xUD
Бренд: XtendLan Страницы: 228
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Бренд: Multitech Страницы: 81
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Бренд: Bitspower Страницы: 6
NCR 7702-K134 Upgrade Manual preview
7702-K134
Бренд: NCR Страницы: 15
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Бренд: PairGain Страницы: 80
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Бренд: S&P Страницы: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Бренд: ProSoft Страницы: 53
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Бренд: Mobatime Страницы: 94
Aaeon FWS-7811 Manual preview
FWS-7811
Бренд: Aaeon Страницы: 100
Abus TVAC21000 User Manual preview
TVAC21000
Бренд: Abus Страницы: 98
Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011 Datasheet preview
2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011
Бренд: Intel Страницы: 172
ZALMAN CNPS8900 Series User Manual preview
CNPS8900 Series
Бренд: ZALMAN Страницы: 10
Atmel SAMA5D31-EK User Manual preview
SAMA5D31-EK
Бренд: Atmel Страницы: 123

Бренды по названию

Популярные бренды

Загрузить еще бренды