Sierra Wireless MP 700 Series Скачать руководство пользователя страница 115

Страница: 115 / 118

Index

quiet mode, 102

Radio Link Protocol

See

RLP.

read, 79

Received Signal Strength Indicator

See

RSSI.

registers, 19, 102, 104– 10 6

registration status, 72, 91

reporting engines, 50

reset, 49

to factory defaults, 58

to stored configuration, 103

response, from modem, 10

framing, 20

result codes, 10, 19

error, 76

framing, 20

incoming calls, 90

listing, 106– 107

suppress, 102

unsolicited, 68, 72

verbose, 102

RLP, 92

RSSI, 95

saving settings, 59

select operator, 84

send, 77

sensors

See

I/O ports.

service center address, 93

service type report, 90

settings, 58, 5 9

factory defaults, 107– 1 08

reset to stored, 103

signal quality, 95

SIM lock, 74

password, 89

PIN entry, 89

SIM sled, 56

SMS messaging, 77, 78, 7 9

commands, 27– 28

delete, 77

format, 78

new, 82

preferred service, 72

read, 79

restore settings, 91

save settings, 92

send, 80

send from storage, 81

service center address, 93

service selection, 94

text mode parameters, 93

write, 81

speaker volume, 101

S-register, 102

state, 15, 86

changing, 102

command, 15

data, 15

data, entering, 64

in combination with condition, 16

in combination with mode, 16

transitioning between, 16

status

activity, 86

status registers, 104– 106

TAIP, 46

commands, sending, 42

temperature, 32

TIES, 52

Time Independent Escape Sequence

See

TIES

timeout, 50

Trimble ASCII Interface Protocol

See

TAIP.

V.42bis compression, 96

verbose mode, 102

version

firmware, 49, 69, 97, 1 01

firmware, current with this guide, 8

voice calls

answer, 100

call forwarding, 60

call waiting, 61

calling line identity, 75

calling line identity restriction, 75

error report, 62

hang-up, 101

list, 73

phone book, 86

speaker volume, 101

voice mode, 15

volume

speaker, 101

Rev 3.2 Oct.05

113

Содержание MP 700 Series























































































































Результаты поиска

Содержание MP 700 Series

Отзывы:

Sierra Wireless MP 700 Series, Справочник по командам, Страница: 115 / 118

Результаты поиска

Содержание MP 700 Series

Отзывы: