Sierra Wireless MP 700 Series Скачать руководство пользователя

Страница: 92 / 118

MP 700 Series GPS AT Command Reference

2130309

+CR=<n>

+CR?

Note: This command
replaces the V.25

ter

command Modulation
Reporting CMR,
which is not appropriate
for use on the GSM
network.

Service reporting control

Sets whether service type is returned (using the result code

+CR: <service>

)

when the modem has determined which speed and quality of service will be
used, but before any error control or data compression reports are transmitted,
and before

CONNECT

is returned.

•

<n>=0

sets the modem not to report the service type.

•

<n>=1

reports service type.

+CR?

returns the current setting.

The

parameter in result codes reports:

•

ASYNC

asynchronous transparent

•

SYNC

synchronous transparent

•

REL ASYNC

asynchronous non-transparent

•

REL SYNC

synchronous non-transparent

Data compression reporting can be enabled with the +DR command (page 96).

+CRC=<n>

+CRC?

Cellular result codes for incoming calls

Sets whether incoming calls or GPRS network requests for PDP context
activation indicate a simple

RING

or a detailed, extended-format result code in

the form

+CRING: <type>

•

<n>=0

disables the extended format, returning only

RING

•

<n>=1

enables the extended format in the form

+CRING: <type>

+CRC?

returns the current setting.

Supported values

Incoming calls or PDP context activation requests report the following values for

+CRING: <type>

<type>=ASYNC

asynchronous transparent

<type>=SYNC

synchronous transparent

<type>=REL ASYNC

asynchronous non-transparent

<type>=REL SYNC

synchronous non-transparent

<type>=VOICE

normal voice

For GPRS context activation, <PDP_type>

and

<PDP_addr>

are as defined in

the Define PDP Context (

+CGDCONT

) command (see page 65).

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

Содержание MP 700 Series























































































































Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды

Sierra Wireless MP 700 Series, Справочник по командам

Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды