Sierra Wireless MP 700 Series Скачать руководство пользователя

Страница: 98 / 118

MP 700 Series GPS AT Command Reference

2130309

+CTMSET=
[<enableMOCtm>],
[<enableCtm>],
[<ctmInterface>],
[ctmBaudotRate>]

+CTMSET=?

+CTMSET?

Note: This command is
only available on the
AirCard 775 and a
customization is required
to enable it.

Enable / disable support for CTM / TTY

Enables and disables support for CTM (Cordless Terminal Mobility). When
enabled, the modem can be used with a TTY (TeleTYpe device). (The TTY is a
device used by the speech and hearing-impaired which connects to the headset
connector on the modem.)

Supported values

<enableMOCtm>:

Mobile originated CTM:

•

Disable

•

Enable

<enableCtm>:

Mobile terminated CTM:

•

Disable

•

Enable

<enableInterface>:

Character set (only Baudot is supported):

•

Baudot

<ctmBaudotRate>:

Modulation rate:

•

45.45 Hz

•

50 Hz

+CTMSET?

displays the current settings and

+CTMSET=?

displays supported

settings.

+DR=<n>

+DR?

V.42

bis

compression reporting

Sets whether the V.42

bis

compression status is returned (using the result code

+DR: <type>

) before going into the online data state, for either originated or

answered calls:

•

<n>=0

sets the modem not to report compression status.

•

<n>=1

reports compression status.

<type>

can be one of four values:

•

NONE

data compression is not in use

•

V42B

Rec. V42

bis

is in use in both direction

•

V42B RD

Rec. V42

bis

is in use in receive direction only

•

V42B TD

Rec. V42

bis

is in use in transmit direction only

+DR?

returns the current setting for reporting.

Service type reporting can be enabled with the

+CR

command (page 90).

V.42

bis

compression is controlled by

+DS

(page 97).

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

Содержание MP 700 Series























































































































Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды

Sierra Wireless MP 700 Series, Справочник по командам

Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды