Sierra Wireless MP 700 Series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 118

background image

MP 700 Series GPS AT Command Reference

66

2130309

+CGEQMIN=[<cid>
[,<Traffic class>
[,<Maximum bitrate
UL>]
[,Maximum bitrate DL>]
[,Guaranteed bitrate
UL>]
[,Guaranteed bitrate
DL>]
[,Delivery order>]
[,Maximum SDU size>]
[,SDU error ratio>]
[,Residual bit error
ratio>]
[,<Delivery of
erroneous SDUs>]
[,<Transfer delay>]
[, <Traffic handling
priority>]

+CGEQMIN?

+CGEQMIN=?

Note: This command is
only available on the
AirCard 775. On other
products use the
command, +CGQMIN,
described on page 70.

Set or Query Minimum Quality of Service Profile

Specifies a minimum acceptable Quality of Service (QoS) profile for the
specified local context identification parameter

<cid>

. (See pages 65 and 70 for

more information.) The modem checks this profile against the negotiated profile
returned in the Activate PDP Context Accept message. If the negotiated profile
does not meet the minimum, the modem ends the data session.

Note: The

D**##

command (used to establish GPRS connections) uses only

those settings assigned to the PDP Context Identifier 1 (that is, <cid>=1).

Note: A special form of the set command,

+CGEQMIN= <cid>

, causes the

minimum acceptable profile for context number

<cid>

to become undefined. In

this case no check is made against the negotiated profile.

Supported values

The set command specifies these parameters:

<cid>

(PDP Context Identifier) is a number corresponding to a PDP context

definition. (See +CGDCONT on page 65

)

<Traffic class>

is a number indicating the application type for which the UMTS

bearer service is optimised where

0

= conversational,

1

= streaming,

2

=

interactive, and

3

= background.

<Maximum bitrate UL>

is a number specifying the maximum speed (kbps) of

uplink traffic delivered to an SAP (Service Access Point).

<Maximum bitrate DL>

is a number specifying the maximum speed (kbps) of

downlink traffic delivered by an SAP (Service Access Point). When this
parameter is set to “0”, the modem requests the subscribed value.

<Guaranteed bitrate UL>

is a number specifying the guaranteed speed (kbps)

of uplink traffic delivered to an SAP (Service Access Point). When this
parameter is set to “0”, the modem requests the subscribed value.

Continued on next page.

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

«
...
66
67
68
69
70
...
»

Содержание MP 700 Series























































































































Отзывы:

Нет отзывов

Похожие инструкции для MP 700 Series

Бренд: NextNet Страницы: 22

Бренд: Best Data Products Страницы: 41

Бренд: FALCOM Страницы: 46

Бренд: jablotron Страницы: 4

Бренд: Magellan Страницы: 10

Бренд: TELUS Страницы: 37

Бренд: Vahle Страницы: 16

Бренд: Moultrie Mobile Страницы: 7

SpeedStream 4200

Бренд: Siemens Страницы: 8

EDGE Speed ES75

Бренд: Siemens Страницы: 4

SpeedStream 4100

Бренд: Siemens Страницы: 9

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 20

Gigaset SX685 WiMAX

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 56

Бренд: Siemens Страницы: 51

SIMATIC NET MODEM MD720

Бренд: Siemens Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды