Sierra Wireless MP 700 Series Скачать руководство пользователя

Страница: 72 / 118

MP 700 Series GPS AT Command Reference

2130309

+CGPADDR
[=<cid>]

+CGPADDR=?

Note: The Sierra
Wireless modem permits
only one PDP context to
be active at a time.

Show PDP address

Returns a list of PDP addresses for the specified context identifier.

The command returns the IP address. The address may be static or dynamic.
For a static address, it will be the one set by the

+CGDCONT

command

(page 65) when the context was defined. For a dynamic address it will be the
one assigned during the last PDP context activation for the specified

<cid>

. If no

address is available, it is omitted.

<cid>

is a numeric parameter which specifies a particular PDP context definition

(see the

+CGDCONT

command, page 65). If no

<cid>

is specified, the address

for the current defined context is returned.

+CGPADDR=?

returns the current defined

<cid>

+CGQMIN
[=<cid>]
[,<precedence >]
[,<delay>]
[,<reliability>]
[,<peak>]
[,<mean>]

+CGQMIN?

+CGQMIN=?

Note: To specify a
particular QoS profile,
rather than the minimum,
use the +CGQREQ
command (page 71).

Set or query minimum acceptable quality of service

Note: If you are using an AirCard 775, use the cCGEQMIN
described on page 66, rather than this command.

Specifies a minimum acceptable Quality of Service (QoS) profile for the
specified local context identification parameter

<cid>

. (See pages 65 and 70 for

more information.) The modem checks the quality of service profile against the
negotiated profile returned in the Activate PDP Context Accept message.

Note: The

D**##

command (used to establish GPRS connections) uses only

those settings assigned to the PDP Context Identifier 1 (that is, <cid>=1).

+CGQMIN?

returns the current settings for each defined context, in the same

order as specified for the set command, while

+CGQMIN=?

returns values

supported as a compound value. The parameter value ranges for each PDP
type are returned on a separate line.

Note: A special form of the set command,

+CGQMIN= <cid>

, causes the

minimum acceptable profile for context number

<cid>

to become undefined. In

this case no check is made against the negotiated profile.

If a value is omitted for a particular class, then that class is not checked.

Supported values

The

+CGQMIN

command is effectively an extension to the

+CGDCONT

command (page 65). The QoS profile consists of a number of parameters, each
of which may be set to a separate value. The

<cid>

value remains as discussed

on pages 65 and 70 . The remaining parameters are all numeric, and defined in
the GSM 03.60 standard:

Continued on next page.

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

Содержание MP 700 Series























































































































Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды

Sierra Wireless MP 700 Series, Справочник по командам

Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды