Sierra Wireless MP 700 Series Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 118

background image

Command Reference

Rev 3.2 Oct.05

57

!MPUSB=<n>

!MPUSB?

Enable / disable USB operation

This command is only available on modems with firmware version 2.0 or
greater.

The MP 750 GPS can be connected to the host PC with either a serial or USB
cable. If only a serial cable is in use, this command has no effect.

If a USB cable is in use, this command enables and disables USB operation, as
specified by

<n>

:

•

<n>=1

Enables USB operation (default)

•

<n>=0

Disables USB operation

If the modem is attached to the host PC by USB cable (or by both a USB and
serial cable), USB operation must be disabled to allow for a DUN (Dial-Up
Networking) connection using

ATD

. (

ATD

is described on page 100.)

The modem must be reset before the command takes effect. (The modem can
be reset using the reset button or the

!MPGRESET

command.)

!MPUSB?

returns the current USB state.

!MPWATCHER=<LAN>,
<NAT>

!MPWATCHER?

Enable / disable NAT support

Note: This command is only available on MP 750 GPS modems with firmware
version R2_2_5ap or later and on MP 775 GPS modems with firmware version
R3_1_0ap or later.

NAT support is required where the MP 750 GPS and the host PC (running
Watcher) are connected to a router, and where the router uses Network Address
Translation (NAT) on the UDP port address. (That is, “port address translation”
NATing.)

This command enables and disables the NAT flag. When enabled the
MP 750 GPS uses the source UDP port number of incoming IP/UDP packets as
the destination UDP port when replying to requests from the host. (When the
NAT flag is disabled, the MP 750 GPS uses the UDP port address that is set
using the

!MPPRIVIP

command. See page 55.)

Continued on next page.

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

«
...
57
58
59
60
61
...
»

Содержание MP 700 Series























































































































Отзывы:

Нет отзывов

Похожие инструкции для MP 700 Series

MultiConnect Cell MTC-LVW2

Бренд: Multitech Страницы: 41

Prestige 650M-17

Бренд: ZyXEL Communications Страницы: 89

Бренд: Ovation Страницы: 19

Бренд: Cisco Страницы: 98

Cisco 2900 series

Бренд: Cisco Страницы: 15

Бренд: Cisco Страницы: 58

Бренд: Cisco Страницы: 2

Бренд: Cisco Страницы: 10

Бренд: Patton electronics Страницы: 10

Бренд: Zte Страницы: 25

Бренд: Microflex Страницы: 10

Бренд: Dynex Страницы: 8

Бренд: W&T Electronics Страницы: 63

Бренд: NETGEAR Страницы: 2

Mini Wifi Smart Plug

Бренд: MJ Intelligent Страницы: 18

Бренд: M2M Страницы: 10

Бренд: US Robotics Страницы: 152

Бренд: Zte Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды