Sierra Wireless MP 700 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 118

background image

MP 700 Series GPS AT Command Reference

42

2130309

!MPGCDUMP

Read crash dump data

This command shows the contents of the memory location to which crash dump
data is written. (See

!MPGCCLR

.) The memory location is overwritten

whenever a crash occurs.

!MPGPSCMD=
<

"

TAIP command

"

>

Send TAIP command to GPS module

This command requires that the module be configured to use the TAIP protocol.
(See

!MPGPSRESET

.)

Note that TAIP commands use “>” as the start delimiter and “<“ as the end
delimiter. For example, to issue the TAIP command QST (which queries the
operational status of the GPS module), you would enter:

AT!MPGPSCMD=

"

>QST<

"

For a listing of TAIP commands see the

TAIP Reference

on the Sierra Wireless

web site (www.sierrawireless.com) or see the Trimble web site
(www.trimble.com). (The GPS module in the modem is the SQ. If no
documentation is available for the SQ, see the

SVeeEight Plus GPS System

Designer Reference Manual

.)

!MPGPSCOMOUT=
<enable>, <save to NV>

Enable GPS output to the AT command port

This command is only available on modems with firmware version 2.0 or
greater.

When GPS output to the AT command port is enabled (the

<enable>

parameter

is set to 1), the MP 750 GPS sends TAIP or NMEA data to the COM port. This
might be used to provide data to a third-party “moving map” application. Setting
the

<enable>

parameter to 0 stops the output. (The default is 0.)

The

<save to NV>

parameter is used to specify whether the

<enable>

setting is

saved to non-volatile memory. If the setting is saved to memory, it persists
across power cycles. (The default is 0, where the <enable> setting is NOT
saved to memory.)

Note: When GPS output to the AT command port is enabled, GPS output
occurs until the DTR line is deasserted or TIES is issued, depending on the
setting made using the command

!MPGPSESC

. (See page 45.)

Continued on next page.

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

«
...
42
43
44
45
46
...
»

Содержание MP 700 Series























































































































Отзывы:

Нет отзывов

Похожие инструкции для MP 700 Series

Бренд: Pacific Crest Страницы: 2

Бренд: Racelogic Страницы: 7

Бренд: PACH & COMPANY Страницы: 4

Бренд: Ebyte Страницы: 38

Бренд: Huawei Страницы: 20

Бренд: Technicolor Страницы: 34

Бренд: Viva Страницы: 7

Бренд: Teledyne Страницы: 3

Бренд: Zte Страницы: 40

Бренд: Microflex Страницы: 10

Бренд: Cermetek Страницы: 19

Бренд: Enfora Страницы: 37

Бренд: Cradlepoint Страницы: 130

Бренд: Aiwa Страницы: 11

Бренд: P1 Страницы: 18

Бренд: Terayon Страницы: 26

Бренд: NETGEAR Страницы: 175

Бренд: Hughes Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды