Sierra Wireless MP 700 Series Скачать руководство пользователя | Manualshive

Страница: 70 / 118

background image

MP 700 Series GPS AT Command Reference

68

2130309

+CGEQREQ=[<cid>
[,<Traffic class>
[,<Maximum bitrate
UL>]
[,Maximum bitrate DL>]
[,Guaranteed bitrate
UL>]
[,Guaranteed bitrate
DL>]
[,Delivery order>]
[,Maximum SDU size>]
[,SDU error ratio>]
[,Residual bit error
ratio>]
[,<Delivery of
erroneous SDUs>]
[,<Transfer delay>]
[, <Traffic handling
priority>]

+CGEQREQ?

+CGEQREQ=?

Note: This command is
only available on the
AirCard 775. On other
products use the
command, +CGQREQ,
described on page 71.

Set or Query Requested Quality of Service Profile

Specifies a Quality of Service Profile to be used when the modem sends an
Activate PDP Context Request message to the network. If the specified profile
is unavailable, the modem returns an error.

Note: A special form of the set command,

+CGQEREQ = <cid>

, causes the

requested profile for context number

<cid>

to become undefined.

If any parameters in the Requested Quality of Service Profile are below those in
the Minimum Quality of Service Profile (set with the cCGEQMIN
described on page 66), the command is rejected and the profile is not updated.

Note: The

D**##

command (used to establish GPRS connections) uses only

those settings assigned to the PDP Context Identifier 1 (that is, <cid>=1).

All parameters are as outlined in

+CGEQMIN

+CGEQREQ?

returns the current settings for each defined context, in the same

order as specified for the set command, while

+CGEQREQ=?

returns values

supported as a compound value. The parameter value ranges for each PDP
type are returned on a separate line.

+CGEREP=
<mode>
[,<buffer>]

+CGEREP?

+CGEREP=?

Unsolicited GPRS event reporting control

Enables or disables sending of unsolicited result codes, which return as
+CGEV: XXX from the modem to the computer in response to modem or
network events.

<mode>

controls the processing of unsolicited result codes specified within this

command, while

<buffer>

controls the effect on buffered codes, depending on

the <mode> setting. Unsupported settings return an error.

+CGEREP?

returns the current mode and buffer settings, while

+CGEREP=?

returns the modes and buffer settings supported by the modem as compound
values.

Continued on next page.

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

«
...
68
69
70
71
72
...
»

Содержание MP 700 Series























































































































Отзывы:

Нет отзывов

Похожие инструкции для MP 700 Series

Бренд: 3Com Страницы: 24

Бренд: Microlink Страницы: 17

Бренд: Novatel Страницы: 148

StormPort DSL Modem

Бренд: Paradyne Страницы: 2

Бренд: Versitron Страницы: 15

MultiModem MT2834ZDX Series

Бренд: Multitech Страницы: 8

Бренд: Toshiba Страницы: 120

G.SHDSL .bis NTU Series

Бренд: XtendLan Страницы: 166

Бренд: upcom Страницы: 13

Бренд: Ebyte Страницы: 17

Бренд: Broadxent Страницы: 60

Бренд: Cradlepoint Страницы: 2

COR IBR1100 series

Бренд: Cradlepoint Страницы: 5

Бренд: Cradlepoint Страницы: 20

Бренд: Telecom Страницы: 8

Бренд: Telecom Страницы: 28

3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux

Бренд: 3Com Страницы: 100

Бренд: 3Com Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды