background image

MP 700 Series GPS AT Command Reference 

78 

2130309 

+CMGF=<n> 

+CMGF? 

Select SMS message format 

Specifies the input and output format of messages to use. 

<n>

 indicates the 

format of messages used with send, list, read and write commands and 
unsolicited result codes resulting from received messages. 

There are two available formats for text messages: 

• 

<n>=0

 specifies PDU (Protocol Description Unit) mode, in which the 

complete SMS message, including all header information, is passed as a 
binary string.. 

• 

<n>=1 

specifies text mode, where the headers and body of the messages 

are given as separate parameters. 

Text mode is an encoding of the bit stream represented by PDU mode. See 

+CMGC

 (page 77) for information on sending messages. 

+CMGF?

 returns the current setting. 

+CMGL 
[=<status>] 

List SMS messages 

Lists messages of the specified 

<status> 

from the message store. If 

<status>

 is 

omitted, the command lists all messages (same as 

<status>=4

). 

The format of the returned messages depends on whether the modem has been 
set to PDU or text mode (see 

+CMGF

, page 78): 

• 

In PDU mode, returned messages appear in the form: 

+CMGL: <index>,<status>,<alpha>, 

<length><CR><LF> 

<pdu data> 

+CMGL: <index>,<status>,<alpha>, 

<length><CR><LF> 

<pdu data> 

etc. 

• 

In text mode, returned messages appear in the form: 

+CMGL: <index>,<stat>,<oa/da>,<alpha>, 

<scts>,<tooa/toda>, <length><CR><LF> 

<message text> 

+CMGL: <index>,<stat>,<oa/da>,<alpha>, 

<scts>,<tooa/toda>, <length><CR><LF> 

<message text> 

[etc.] 

Continued on next page. 

Table 3-9:  Command Reference Table (ASCII Alphabetic) 

Command 

Description 

Содержание MP 700 Series























































































































Отзывы: