Siemens TXP-CLC Скачать руководство пользователя | Manualshive

Страница: 171 / 216

background image

TXP CLC Course

11

Total drive run time (TGL)

Name: TGL
Function: Defines the total run time of the drive between the limit positions after a
command output, for alarm and indication (only effective with both RWE and
RWA set at 3)
Range of values: 0 to 60,000
Meaning:

0 = no run time monitoring
60,000 = 6,000 s (adjusting steps: 0.1 s)

Default setting:

10 = 1 s

Effect of Feed-back message on command execution

Name: WRBHAEA; WRBHAAZ; WRBSEA; WRBSAZ
Function: Defines whether manual, automatic and protection On and Off
commands are to be blocked when a feed-back fault is active in the command
direction
Range of values: blocked/not blocked
Meaning:

blocked = blocks command execution
not blocked = command is executed

WRBHAEA = MANUAL/AUTOMATIC ON blocked/not blocked
WRBHAAZ = MANUAL/AUTOMATIC OFF blocked/not blocked
WRBSEA = PROTECTION ON blocked/not blocked
WRBSAZ = PROTECTION OFF blocked/not blocked

Basic setting: blocked

Effect of status discrepancy/monitoring

Name: WEFSPERR; WEFNSEA; WEFNSAZ
Function: Defines whether limits are monitored and if the protection On and Off
commands should be blocked when a status discrepancy fault is detected
Range of values: blocked/not blocked
Meaning:

WEFSPERR = blocked status discrepancy monitoring disabled
WEFSPERR = not blocked status discrepancy monitoring enabled

WEFNSEA = PROTECTION ON command blocked/not blocked
WEFNSAZ = PROTECTION OFF command blocked/not blocked

Basic setting: blocked

Slowing-down time for travel-dependent disconnection (NLZ)

Name: NLZ
Function: Defines how long the command output signal is maintained after the
feedback input signal is received for torque close or open.
Range of values: 0 to 100
Meaning:

0 = no delayed disconnection
100 = 10 s disconnection delay

Basic setting:

0

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

15

«
...
169
170
171
172
173
...
»

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TXP-CLC

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: FAAC Страницы: 14

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: D+H Страницы: 14

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: R. Beck Maschinenbau Страницы: 35

Бренд: QUALITY LIFTS Страницы: 21

Бренд: Saluki Страницы: 13

Бренд: LLURIA Страницы: 2

Бренд: Daihan Scientific Страницы: 11

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренд: Toro Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды