Siemens TXP-CLC Скачать руководство пользователя | Manualshive

Страница: 161 / 216

background image

TXP CLC Course

11

Operating Modes

Operating mode is selected based on the parameters “RMS”, “VBAF”, “MAUS”,
“REJ/MAN”, “OP_MODE“; the inputs “VOS”, AUTO”, “MAN”; and the operating
window buttons of the OM650.

The “SEMI” or semiautomatic mode is selected if the parameter “RMS” is set to
“TAG OUT NO”. For any other operating mode, the parameter “RMS” should be
set to “TAG OUT YES”.

The “VBAF” parameter allows a manual or automatic close command even if the
DCM block is in an alarm condition. The “REJ/MAN” parameter forces the
operating mode to manual if manual mode is allowed and the block is in alarm.

The “MAUS” parameter allows a changeover from manual to automatic either
from the operating window of the OM650 or from the “AUTO” or “MAN” logical
inputs to the DCM block.

The “OP_MODE” parameter selects between the three options shown below.
Once an operation mode is selected, the DCM block can only operate in the
modes named under “Selection”.

OP_MODE

Selection

Automatic
Commands

Manual
Commands

AUTO/MAN Manual

Automatic

Deactivated
Activated

Activated
Deactivated

SEMI/MAN Manual

Semi-automatic

Deactivated
Activated

Activated
Activated

SEMI Semi-automatic

Activated

Activated

Automatic activated means that automatic commands are effective and manual
commands are disabled; Semi means that manual and automatic commands are
effective; and Manual means that manual commands are functional and
automatic commands are disabled. The switchover and indication of the
operating modes “Automatic”, “Semi” or “Manual” is done via the operating
window of the OM 650 or in the logic. No distinction between the operating
modes “Automatic” and “Manual” can be made if the TAG-OUT function is not
activated with the parameter RMS.

The “VOS” input (local control) deactivates all manual, automatic or semi-
automatic commands and allows the feedback to change with local commands
without initiating alarm conditions. The protection commands are still active.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

5

«
...
159
160
161
162
163
...
»

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TXP-CLC

Бренд: OmarLift Страницы: 14

Бренд: Waterway Страницы: 16

Бренд: Datavideo Страницы: 8

Бренд: Danfoss Страницы: 24

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Taie Страницы: 28

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Lamtec Страницы: 22

Бренд: Mackie Страницы: 4

Бренд: Water Specialist Страницы: 60

traxon e:cue LCE-mx

Бренд: Osram Страницы: 35

Бренд: Savant Страницы: 2

Бренд: Technische Alternative Страницы: 68

Бренд: Hiwin Страницы: 99

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Planar Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды