manualshive.com logo in svg

Siemens TXP-CLC, Руководство пользователя

Поделиться
Скачать
Siemens TXP-CLC Скачать руководство пользователя страница 124

 
 

 

 

 

TXP CLC Course

 

 

 
In normal operation, the AT references the value of the input signal from the 
Process Image Input Table (PAED), conditions it and writes it into the status data 
block (ZUDB).  
 
The signal must be defined (SIGDEF) on the individual level logic diagram 
(function plan / YFR) that is identified with the Power Plant Identification Code 
(KKS) for the equipment. The signal is then available for use in the AP. The 
SIGDEF and KKS must match the input channel identifier in the parameter mask 
of the SIM module on the rack level location drawing for the connection to the 
input point. 
 
 
 

 
Outputs to other Logic Diagrams 

 

Name Description 

AI/SIG 

Analog input signal 

GS1 

Limit signal 1 

GS2 

Limit signal 2 

GS3 

Limit signal 3 

GS4 

Limit signal 4 

KSIM 

Analog input signal simulated 

KG 

Analog input signal ok 

 

 

 

 

Inputs from other Logic Diagrams 

 

Name Description 

KORR Correction 

factor 

 

The KORR input port is used in conjunction with the MOD parameter (see 
parameters) to input a multiplication factor for correction calculations. 

Training Center

 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

2

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды