manualshive.com logo in svg

Siemens TXP-CLC, Руководство пользователя

Поделиться
Скачать
Siemens TXP-CLC Скачать руководство пользователя страница 72

 
 

 

 

 

TXP CLC Course

 

 

 

 

MIN limit value 

 
For a MIN limit value the switching point is obtained by changing the measured 
variable in relation to a minimum value, i.e. < MIN. For the MIN limit value the     
<  MIN signal is derived from the NCC of the switching device. Figure 8 and 9 
show examples of < MIN signals for pressure and level. The < MIN signals are 
assigned serial numbers of XG52 and NOT MIN signals are assigned serial 
numbers of XG02. 

 
 
 

MIN 

 

 

      

 

 

 

 

NOT 

MIN 

XG52 

 

XG02 

    XG52 

 

 

 

 

 

 

XG02 

 

            50 

 

 

 

 

 

        100 

          PSIG 

 

 

 

 

 

        PSIG 

 

 

   

          Pressure   

 

 

 

 

       Pressure 

          NCC         NOC 

 

 

 

 

          NCC       NOC 

 
 
 
 

 

   

           Set-point   

 

 

 

 

       Set-point 

 

 

   

          

≤

 75 PSIG   

 

 

 

 

      

≤

 75 PSIG 

 

 

 

 

Pressure 

≤

 MIN

 

 

 

 

Pressure NOT MIN or 

>

 MIN 

 
 

 

 

   

 

Figure 8  -  MIN Signal (Pressure)  -  XG52/XG02 

 

 
 
 

MIN

   

   

 

 

 

 

     

NOT MIN 

XG52 

 

XG02 

    XG52 

 

 

 

 

 

 

XG02 

 
 
 
 

 

   

             Level 

 

 

 

 

 

          Level 

           NCC       NOC 

 

 

 

 

          NCC       NOC 

 
 
 
 
 
 
 

 

 

      Level 

≤

 

MIN 

    Level 

NOT 

MIN 

or 

>

 MIN 

 
 

 

   

 

Figure 9  -  MIN Signal (Level)  -  XG52/XG02 

Training Center 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

 

26 

26 

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды