Siemens TXP-CLC Скачать руководство пользователя | Manualshive

Страница: 173 / 216

background image

TXP CLC Course

11

Reject to manual (REJ/MAN)

Name: REJ/MAN
Function: Defines whether the operation mode set to manual in the event of a
fault or failure. Can only be activated by enabling TAG-OUT via parameter RMS.
Range of values: Not activated / activated
Basic setting:

Not activated.

Operation mode (OP_MODE)

Name: OP_MODE
Function: Defines the possible operating modes. Can only be activated by
enabling TAG-OUT via parameter RMS.
Range of values: AUTO / MAN

SEMI

SEMI

/

MAN

Basic setting:

AUTO / MAN.

Behavior on switchgear fault (BSFG)

Name: BSFG
Function: Defines whether it is possible to initiate a manual “OFF” command from
OM650 while the switchgear, breaker or motor starter is in fault (SAG). Can only
be activated by enabling TAG-OUT via parameter RMS.
Range of values: Not activated / activated
Basic setting:

Not activated

Inputs from other logic (not I/O type inputs)
Name Description

SQ

Group alarm acknowledgement

BL/OM Block

OM

operating

BL/AP

Block alarm protection command

A/ON

Auto command on

A/OFF

Auto command off

SGC Under

voltage limit signal

P/ON

Protection command on

P/OFF

Protection command off

EN/ON Enabling

on

EN/OFF Enabling

off

VOS Local

controlling

AUTO

Priority switch man/auto

MAN

Priority switch auto/man

FB/OFF Feedback

off

SGF Switchgear

fault

FB/ON Feedback

on

ANB

Feeder not ready for operation

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

17

«
...
171
172
173
174
175
...
»

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TXP-CLC

Бренд: Ohsung Electronics Страницы: 18

Бренд: jbc Страницы: 44

Бренд: jbc Страницы: 8

Бренд: RADVision Страницы: 3

Бренд: RADEMACHER Страницы: 48

Бренд: R&M Страницы: 53

Бренд: NAiS Страницы: 144

Бренд: Audioaccess Страницы: 2

SaunaLogic SL2 Control

Бренд: Finnleo Страницы: 14

Бренд: Daikin Страницы: 64

Q.PEAK DUO BLK ML-G10/t Series

Бренд: Qcells Страницы: 13

Бренд: Fantini Cosmi Страницы: 25

Бренд: Grundfos Страницы: 16

Бренд: Loewe Страницы: 62

Бренд: Shimaden Страницы: 32

VARIOMATIC SARV 07.1

Бренд: AUMA Страницы: 32

Бренд: HIMA Страницы: 58

SmarTemp Control fx

Бренд: Webasto Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды