Siemens TXP-CLC Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 216

Siemens TXP-CLC Скачать руководство пользователя страница 16

TXP-CLC

Course

AS 620 T
The fast closed loop control for the turbine

SIMADYN processing units

SIMADYN processing units

for fast closed loop controls

for fast closed loop controls

(position control: 4 ms for

(position control: 4 ms for

gas and steam turbines)

gas and steam turbines)

Fast signal conditioning

Fast signal conditioning

with SIM T (1 ms)

with SIM T (1 ms)

1 out of 2 redundancy design

1 out of 2 redundancy design

for closed loop controls

for closed loop controls

Fully integrated Communication

Fully integrated Communication

Capable of loop processing

Capable of loop processing

time as low as .2 ms

time as low as .2 ms

The AS620 T automation system is used for the closed-loop control of gas and
steam turbines as well as for the voltage control of generators. Closed-loop
control functions for the turbine generator set include:

•

Speed

controller

•

Output

controller

•

Pressure

controller

•

Position

controller

•

Terminal voltage controller

•

Excitation current controller

The AS620 T comprises the automation processor system APT, using SIMADYN
components, and an associated AP as a head station. Both components are
coupled to the plant bus via their respective communications processors. The
high-speed controllers for the turbine generator set are implemented in the APT
using a STRUC G work-station. Communication with the other components of
TXP takes place via the head station. In addition to high-speed control, other I&C
tasks for the turbine generator set can also be performed in the AP.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

4

«
...
14
15
16
17
18
...
»

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды