Siemens TXP-CLC Скачать руководство пользователя | Manualshive

Страница: 159 / 216

background image

TXP CLC Course

11

Mode of Operation

Motor Drive

Standard Application:

•

Plug-in Switchgear unit with 2 contactor relays (one per command
direction)

•

Latching in the switchgear

•

1 NO/NC contact on main contactor

When latching in the switchgear, the

command output

(ALA or ALE) is reset

after the feed-back message (RME or RMA) arrives to reduce power losses on
the module. This function must be configured with parameter “BAV”.

Solenoid Valve

Standard Application:

•

Plug-in Switchgear unit with:

2 contactor relays

or 1 contactor relay

•

Latching in the control system

•

Limit

switches:

1 NO/NC contact on the contactor

or 1 NO/NC contact on the valve

When latching in the control system the

command output

(

ALA or ALE

)

is not

reset after the feed-back message (RME or RMA) arrives. This function is
configured.

The control command is permanently output by the module (configurable with
parameter “BAV” ) in the case of switchgear without latching. In this case, a
change in the command output (from “On” to “Off”) only takes place with the
counter (opposite) command.

The logic functions correspond to those of a motor drive. It is possible to have
applications where only one contactor relay is connected to the command output
(preferably on (ALE) but can be either on or off).

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

3

«
...
157
158
159
160
161
...
»

Содержание TXP-CLC

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TXP-CLC

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: Galcon Страницы: 32

Бренд: Sanhua Страницы: 3

Бренд: rav Страницы: 120

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

Бренд: RAPIBREW Страницы: 16

Бренд: Ziton Страницы: 28

Бренд: Unico Страницы: 164

Бренд: DANIEL Страницы: 48

Бренд: TEL Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды