Siemens SIJECT15 Скачать руководство пользователя | Manualshive

Страница: 88 / 91

background image

SIJECT OP15B Screens

SIJECT 15/16 Operation Manual June, 2003

3-54

Injection during mold adjustment (Inject)

－

in mold adjustment mode,

set the pressure and flow during injection.

Suck back during mold adjustment (SuckBck)

－

in mold adjustment

mode, set the pressure and flow during suck back (decompression).

Charging during mold adjustment (Charge)

－

in mold adjustment

mode, set the pressure and flow during charging.

Mold advance during mold adjustment (Advance)

－

in mold

adjustment mode, set the pressure and flow during mold advance.

Mold retract during mold adjustment (Retract)

－

in mold adjustment

mode, set the pressure and flow during mold retract.

Pulse of mold advance (AdvPuls)

－

in pulse mold adjustment mode,

set the pulse of mold advance.

Pulse of mold retract (RetPuls)

－

in pulse mold adjustment mode, set

the pulse of mold retract.

Pulse mold adjustment

(PulsAdj)

– select or deselect.

Mold close time (MldCloTim)

－

in Auto adjustment mode, set the mold

close time for mold adjustment. Users can set an initial value and the
system will judge it automatically. If mold cannot be adjusted within this
time, then the system will retract the mold to fulfil automatic adjustment.

Auto mold adjustment (AutoAdj)

－

select or deselect.

Current status (CurStatus)

－

display the pressure and flow of current

system.

When pulse adjustment mode is selected, press advance key

and

the system will run the set pulse to make the mold advance. Press

retract key

and the sytem will run the set pulse to make the mold

retract.

When auto adjustment mode is selected, press soft key F4 “Auto Start”
to start the auto mold adjustment; and press F5 “Auto Stop” to end the
adjustment.

«
...
86
87
88
89
90
...
»

Содержание SIJECT15




























































































Отзывы:

Нет отзывов

Похожие инструкции для SIJECT15

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Daikin Страницы: 48

Бренд: Daikin Страницы: 77

Бренд: Daikin Страницы: 32

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 14

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 1

Бренд: jablotron Страницы: 2

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 2

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: National Instruments Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды