Siemens SIJECT15 Скачать руководство пользователя

Страница: 69 / 91

SIJECT

OP15B

Screens

SIJECT 15/16 Operation Manual

3-35

Fig 3-29

Service screen 2.3 – temperature setting

Temperature setting

On service screen 1, press softkey F2

to enter service screen 2 --

- linear scale setting. Then, press softkey F4

so as to enter

temperature setting screen. Temperature channel can be set from 1 to 5,
and temperature can be set accordingly.

Temperature Tolerance Plus

--- set the tolerance plus for each

temperature channel.

Temperature Tolerance Minus

--- set the tolerance minus for each

temperature channel.

Oil Upper

--- set the upper limit of hydraulic oil temperature.

Oil Lower

--- set the lower limit of hydraulic oil temperature.

Temperature Compensation

--- set the temperature compensation. The

system has been set the compensation before delivery, and it is
unnecessary for users to set it again.

Nozzle Mode

--- two modes are available, it can be assigned as close-

loop or open-loop.

Channel 1

--- select or deselect

Channel 2

--- select or deselect

Channel 3

--- select or deselect

Channel 4

--- select or deselect

Channel 5

--- select or deselect

Oil Temperature Alarm

--- If oil temperature alarm is selected: when the

upper/lower limit of oil temperature has been set, there is no alarm if oil
temperature is within the specification and alarm occurs if it is out of
specification.

Содержание SIJECT15




























































































Результаты поиска

Содержание SIJECT15

Отзывы:

Похожие инструкции для SIJECT15

Бренды по названию

Популярные бренды

Siemens SIJECT15, Руководство по эксплуатации

Результаты поиска

Содержание SIJECT15

Отзывы:

Похожие инструкции для SIJECT15

Бренды по названию

Популярные бренды