Siemens SIJECT15 Скачать руководство пользователя страница 87

Страница: 87 / 91

SIJECT

OP15B

Screens

SIJECT 15/16 Operation Manual

3-53

3.2.9 Mold adjustment screen

Fig 3-41

Mold adjustment screen

Operating sequences

Press the mold adjustment key to enter the mold adjustment screen.

Press Mold adjustment mode key

on the operator panal to make

the machine at mold adjustment status. The indicators

②

on the screen

(see table 3-1) is flashing to inform users that the machine is under
adjustment.

The system provides two mold adjustment modes: pulse adjustment and
automatic adjustment.

For pulse adjustment, users can set pulse value for mold adjustment.

For automatic adjustment, users should first set time. If mold adjustment
does not finish within the preset time, then the system will retract the
mold automatically.

Mold close during mold adjustment (MldClo)

－

in mold adjustment

mode, set the pressure and flow during mold close.

Mold open during mold adjustment (MldOpn)

－

in mold adjustment

mode, set the pressure and flow during mold open.

Carriage movement during mold adjustment (Carriage)

－

in mold

adjustment mode, set the pressure and flow during carriage movement.

Ejector during mold adjustment (Ejector)

－

in mold adjustment mode,

set the pressure and flow during ejector movement.

Содержание SIJECT15




























































































Результаты поиска

Содержание SIJECT15

Отзывы:

Похожие инструкции для SIJECT15

Бренды по названию

Популярные бренды

Siemens SIJECT15, Руководство по эксплуатации

Результаты поиска

Содержание SIJECT15

Отзывы:

Похожие инструкции для SIJECT15

Бренды по названию

Популярные бренды