Siemens SI120 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 100

background image

Outputs

49

Siemens Building Technologies

Fire Safety & Security Products

07.2009

8.2.29 Chime

Chime

The chime function can be enabled for the burglar alarm inputs. This function permits the activation of the
keypad buzzer and the "Chime" output in the event of an input being triggered during unset. The buzzer is
activated for a short beep and the "Chime" output for one pulse.
For the buzzer (keypads and outputs), this function can be programmed as a separate parameter.
The chime function can be switched off in the general menu by the user simply by pressing the @ key.

8.2.30 Trouble

(System)

Trouble (System)

This output is activated in the following cases:

z

Fault in telephone line

z

Mains power supply fault

z

Battery fault

z

Failure of fuses

z

E-Bus fault

z

Transmission fault

The output is automatically reset after the end of the fault. In the case of transmission faults, it is also reset
by entering a valid user PIN.

8.2.31 Blockschloss

Blockschloss

The output is always activated except on unset or part set during:

z

Fault

z

Tamper

z

Burglar alarm

z

Alarm in memory

z

Triggered burglar inputs without delay

z

Triggered panic alarm inputs

z

Triggered lock supervision

z

more than 50% of inputs in the partition are bypassed

8.2.32 Blockschloss

2

Blockschloss 2 GV
(Geistiger Verschluss /
Intellectual lock)

The same function as "Blockschloss for Germany" on unset / part set.
In set state the output isn’t activated either. The output in set state is controlled from a remote keypad or an
input which is programmed to "Intellectual lock".
There are two possibilities available in the partition parameters for the intellectual lock:

"GV for unset only":

This means that a “Blockschloss” with a "reset lockout" must be present. In the locked

state either a PIN code must be input on the GV remote keypad or a GV input activated. When this is done,
the block lock GV output is activated for 20 seconds, which means that the operator has 20 seconds in which
to open the “Blockschloss” and unset the system.

"GV for set and unset only":

In this case a code has not only to be entered as described above to unset

the system but also to set it. The time is also limited to 20 seconds during setting.

8.2.33 Blockschloss

Bosch

Blockschloss Bosch

For Blockschloss made by Bosch.

«
...
47
48
49
50
51
...
»

Содержание SI120





































































































Отзывы:

Нет отзывов

Похожие инструкции для SI120

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: jablotron Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: OES Страницы: 3

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

Бренд: Jäger Страницы: 18

Бренд: GEA Страницы: 13

Бренд: Kampmann Страницы: 5

Бренд: Viking Страницы: 4

GA Figure 220-D

Бренд: Vag Страницы: 6

Бренд: DeLaval Страницы: 102

Бренд: Netro Страницы: 14

Бренд: Rain Bird Страницы: 11

LOOPDRIVE FIM-RC

Бренд: 4EVAC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды