Siemens SI120 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 100

background image

Inputs

25

Siemens Building Technologies

Fire Safety & Security Products

07.2009

6.3.17 Audible Panic Alarm

Audible Panic Alarm
UK, HU, BE

Panic alarm with activation of the bell and strobe light outputs. This input acts, regardless of the setting,
on the panic alarm output. In the case of physical inputs, a direct alarm takes place when the keys of the
remote keypad are pressed and held for at least 2 seconds (refer to remote keypad instructions). The
"Panic Alarm" output is latched until the alarm is rest.
Input triggered

Æ

Panic alarm in the assigned partition.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

X X X External

bell

X X 2 Internal

bell

X X X Strobe

light

X X Cannot

full

set

X

Cannot part set

X X X Alarm

in

memory

X X X Panic

alarm

5 5 5 Buzzer
X

X

X

Panic alarm system transmission line

X

X

X

Panic alarm partition transmission line

X X X Transmission

line

input

Partition parameters:
X =

Triggering regardless of the partition mode.

2 =

Triggering only if the internal bell “When Full Set” in the partition parameter is chosen.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

Audible Panic Alarm
All other country versions

Panic alarm with activation of the bell and strobe outputs. This input acts, regardless of the setting, on
the panic alarm output, which on triggering is activated for 10 seconds. In the case of physical inputs, a
direct alarm takes place when the keys on the remote keypad are pressed and held for at least 2 sec-
onds (refer to remote keypad instructions).
Input triggered

Æ

Panic alarm in the assigned partition.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

X X X External

bell

X X 2 Internal

bell

X X X Strobe

light

X X Cannot

full

set

X

Cannot part set

X X X Alarm

in

memory

X X X Panic

alarm

(10

seconds)

X

X

Block lock not released

5 5 5 Buzzer
X

X

X

Panic alarm system transmission line (10 seconds)

X

X

X

Panic alarm partition transmission line (10 seconds)

X

X

X

Transmission line input (10 seconds)

Partition parameters:
X =

Triggering regardless of the partition mode.

2 =

Triggering only if internal bell parameter “When Part Set” is chosen.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

«
...
23
24
25
26
27
...
»

Содержание SI120





































































































Отзывы:

Нет отзывов

Похожие инструкции для SI120

Бренд: ABB Страницы: 2

Бренд: Haier Страницы: 58

Бренд: Lawler Страницы: 4

Бренд: HABONIM Страницы: 9

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: Lamtec Страницы: 22

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: WAC Страницы: 5

Бренд: Sabiana Страницы: 60

F&G Xcomfort CRCA-00/02

Бренд: Moeller Страницы: 4

Бренд: Apricus Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды