Siemens SI120 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 100

background image

System

68

Siemens Building Technologies

Fire Safety & Security Products

07.2009

12.10 Print Style

Disable

The specific separator is disabled for log logbook printing.
The CR/LF is is used to separate fields.

Enable

A specific separator is used for logbook printing.
CR/LF is replaced by #.
Examples:
266#30/06/20 10:56:47# > #TROUBLE #INITIALISATION
267#30/06/20 10:57:03# > #BEGIN #LOCAL ACCESS
268#30/06/20 10:57:04# > #END #LOCAL ACCESS
269#30/06/20 10:57:12# > #BEGIN ALARM #I1/MAIN PCB #INPUT 1
270#30/06/20 10:57:16# > #END ALARM #I1/MAIN PCB #INPUT 1

12.11 Flow Events Sort

[TM5178] Print

This parameter is only accessible via keypad.
It can be used to sort / filter events stored in log book . Possible filter are:

z

Alarms

z

Set / Unset

z

Transmission

z

Tamper

z

Trouble

12.12 Engineer Reset on

[TM4] Alarm Types

This parameter defines how the engineer reset works on the system. You can choose between Tamper-,
Burglar- and Panic alarm.

z

Tamper alarms

z

Burglar alarm

z

Panic alarms

NOTE

You have to activate it for each partition separately in the menu partitions.

«
...
66
67
68
69
70
...
»

Содержание SI120





































































































Отзывы:

Нет отзывов

Похожие инструкции для SI120

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: iluminize Страницы: 2

Бренд: FEAS Страницы: 4

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: Viking Страницы: 4

GA Figure 220-D

Бренд: Vag Страницы: 6

Бренд: Baier Страницы: 20

Бренд: H3C Страницы: 16

Бренд: Yale Страницы: 2

Бренд: Tate Страницы: 32

Бренд: We Страницы: 27

Бренд: Hahnel Страницы: 36

Бренд: maxon motor Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды