Siemens SI120 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 100

background image

Inputs

24

Siemens Building Technologies

Fire Safety & Security Products

07.2009

6.3.16 Silent Panic Alarm

Silent Panic
Alarm
UK, HU, BE

A silent panic alarm is triggered, e.g. neither the outputs for strobe lights nor those for the bells are activated. This input acts
on the panic alarm output regardless of the set state. In the case of physical inputs, a direct alarm takes place when the keys
on the remote keypads are pressed and held for at least 2 seconds (refer to remote keypad instructions).
The output "Panic Alarm" remains stored until alarm is reset.
The "Alarm in Memory" and "Cannot Set” remote keypad LEDs are not activated until a PIN for the corresponding partition is
input.
Input triggered

Æ

Silent panic alarm in assigned partition.

Partition mode:

Unset
Part

set

Full set

Effects on the following outputs when the below partition parameters are preset:

X

X

Cannot full set

X

Cannot part set

X

X

X

Alarm in memory

X X

X

Panic

alarm

X

X

X

Panic alarm system transmission line

X

X

X

Panic alarm partition transmission line

X

X

X

Transmission line input

X =

Triggering regardless of the partition mode.

Silent Panic
Alarm
All other
country
versions

Silent panic alarm is triggered, e.g. neither the outputs for strobe lights nor those for the bells are activated. This input acts
on the panic alarm output, which is activated for 10 seconds on a triggering, regardless of the set state. In the case of physi-
cal inputs, a direct alarm takes place when the keys on the remote keypads are pressed and held for at least 2 seconds
(refer to remote keypad instructions).
Input triggered

Æ

Silent panic alarm in assigned partition.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

X

X

Cannot full set

X

Cannot part set

X

X

X

Alarm in memory

X

X

X

Panic alarm output (10 seconds)

X

X

Block lock output not enabled

X

X

X

Panic alarm system transmission line (10 seconds)

X

X

X

Panic alarm partition transmission line (10 seconds)

X

X

X

Transmission line input (10 seconds)

X =

Triggering regardless of the partition mode.

«
...
22
23
24
25
26
...
»

Содержание SI120





































































































Отзывы:

Нет отзывов

Похожие инструкции для SI120

Бренд: Barco Страницы: 6

Бренд: National Instruments Страницы: 29

Бренд: Harmonic Drive Страницы: 85

Бренд: Lawler Страницы: 5

Бренд: Maestra Страницы: 22

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Trane Страницы: 72

Бренд: East Coast Datacom Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды