Siemens SI120 Скачать руководство пользователя страница 44

Страница: 44 / 100

Outputs

Siemens Building Technologies

Fire Safety & Security Products

07.2009

8.2.1 Unused

Unused

The output is by default not activated and not to use.
Exception: The “unused” output can be activated by the card reader [TM25].

8.2.2 External

Bell

External Bell

This output is activated in the event of the following states when the partition parameters are preset.

Partition mode:

Unset

Part set

Full set

Effects on the following events when the below partition parameter are preset:

1 X Tamper

alarm

1 X Burglar

alarm

X X X Panic

alarm

Fire alarm (pulsating 2 seconds)

Radio unset (0.5 seconds)

Radio full set (2 x 0.25 seconds)

Radio forced full set (4 x 0.25 seconds)

Partition parameters:
X =

Triggering is

always activated regardless of the set state.

1 =

Triggering only "When Part Set" in the partition parameters is chosen.

8 =

Triggering only if "By Fire" in the partition parameter is chosen.

9 =

Triggering only if "RF Confirm" in the partition parameter is chosen.

()= Activation of “Duration” (one time per partition) is defined in the menu partition.

8.2.3 Internal

Bell

Internal Bell

This output is activated in the event of the following states when the partition parameters are preset.

Partition mode:

Unset

Part set

Full set

Effects on the following events when the below partition parameter are preset:

Tamper

alarm

Burglar

alarm

X X X Panic

alarm

Fire alarm (pulsating 2 seconds)

Partition parameters:
X =

Triggering is

always activated regardless of the set state.

2 =

Triggering only "When Full Set" in the partition parameters is chosen.

8 =

Triggering only if "By Fire" in the partition parameter is chosen.

()= Activation of “Duration” (one time per partition) is defined in the menu partition.

8.2.4 Fire

Bell

Fire Bell

This output is activated regardless of the set state.
The “Fire Bell Duration” activation can be defined (per partition) in the partition parameters as either continu-
ous or pulsation (2 seconds)

Содержание SI120





































































































Результаты поиска

Содержание SI120

Отзывы:

Похожие инструкции для SI120

Бренды по названию

Популярные бренды

Siemens SI120, Руководство по настройке

Результаты поиска

Содержание SI120

Отзывы:

Похожие инструкции для SI120

Бренды по названию

Популярные бренды