Chapter 13
Unicast and Multicast Routing
RUGGEDCOM ROX II
CLI User Guide
480
Configuring BGP
NOTE
In complex legacy networks, RIP, OSPF, BGP and IS-IS may all be active on the same router at the same
time. Typically, however, only one dynamic routing protocol is employed at one time.
CONTENTS
•
Section 13.8.1, “Configuring BGP”
•
Section 13.8.2, “Managing Route Maps”
•
Section 13.8.3, “Managing Prepended and Excluded Autonomous System Path Filters”
•
Section 13.8.4, “Managing Prefix Lists and Entries”
•
Section 13.8.5, “Managing Autonomous System Paths and Entries”
•
Section 13.8.6, “Managing Neighbors”
•
Section 13.8.7, “Managing Networks”
•
Section 13.8.8, “Managing Aggregate Addresses”
•
Section 13.8.9, “Managing Aggregate Address Options”
•
Section 13.8.10, “Managing Redistribution Metrics”
•
Section 13.8.11, “Managing Route Reflector Options”
•
Section 13.8.12, “Viewing the Status of Dynamic BGP Routes”
•
Section 13.8.13, “Resetting a BGP Session”
Section 13.8.1
Configuring BGP
To configure dynamic routing with BGP, do the following:
1. Make sure the CLI is in Configuration mode.
2. Navigate to
routing » bgp
and configure the following parameter(s) as required:
Parameter
Description
enabled
Enables BGP.
as-id { as-id }
Synopsis:
A 32-bit unsigned integer between 1 and 65535
Autonomous System ID.
always-compare-med
Always comparing MED from different neighbors.
reachability-check
Synopsis:
{ true, false }
Default:
true
Enables or disables the reachability check for advertised routes.
When enabled, before advertising a self-generated BGP route to other BGP peers, the BGP
daemon checks if the advertised route is reachable locally by default before advertising it
to other BGP peers. The route is only advertised if it exists in the kernel routing table.
default-local-preference { default-local-
preference }
Synopsis:
A 32-bit unsigned integer
Default:
100
Default local preference value.
deterministic-med
Pick the best-MED path among paths advertised from neighboring AS.
Содержание RUGGEDCOM ROX II
