Siemens MK8000 MP4.30 Скачать руководство пользователя страница 53

Страница: 53 / 92

Configuring the MK8000

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

4.5

Connecting networks to the MK8000

Now you need to connect the control units and the network components with the
network drivers in the MK8000 server.

4.5.1

What to drag to the drivers

Cerloop Network



Drag the MK7022 to the Cerloop Driver.

Fig. 49 Connecting the MK7022 to the Cerloop Driver

CS11 and FC700A fire systems can also be connected to the NS8010 Driver. In
these cases, the CK11 and FG700A interfaces should be dragged to the driver, re-
spectively. See 4.7.1 below.

CDI-Net Network



Drag the appropriate CMS or upstream line to the CDI-Net Driver.

The CMS or upstream lines are located in the following areas:



GW20



CMSPad



line ‘n’ (for GW20)

Содержание MK8000 MP4.30





























































































Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды

Siemens MK8000 MP4.30, Руководство по установке и настройке

Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды