Siemens MK8000 MP4.30 Скачать руководство пользователя страница 73

Страница: 73 / 92

Tips for Integrating with an OPC client

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

Here are some general guidelines:



For a distributed configuration, the OPC Server and Clients must be part of the

same workgroup or domain.



On a workgroup network all users who will have access to the OPC server must

belong to this workgroup.



On a workgroup network, an account with the same username/password com-

bination must be created on the server and client stations.



If necessary, adjust DCOM settings: instructions for the DCOM settings are

given in the next section.

Note

: If there is a loss of communication between the MK8000 OPC Server and

one of the client stations, it will not be reported by the MK8000 to the other clients.

Содержание MK8000 MP4.30





























































































Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды

Siemens MK8000 MP4.30, Руководство по установке и настройке

Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды