Siemens MK8000 MP4.30 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 92

background image

Configuring the MK8000

64

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

4.11.1 Verifying the MK8000 license

Each MK8000 license supports a limited number of data points (according to what
was purchased). Specifically, the limitation applies to the total number of control
units and devices configured in Composer.

Note that the licensing mechanism has been changed in MP3.18. Previously, the
limitation was related to the number of OPC items dynamically connected.

As for the MM8000 license, the MK8000 OPC server license calculation is now
based on the static information of the Composer project. More precisely, the li-
cense parameters are the:

–

physical subsystems configured

–

physical objects configured for each subsystems

–

network drivers configured and connected to subsystems

The Composer tool can provide in any moment the required license parameters
and check them against the values currently set.

As shown in Fig. 65, select the

MK8000

node and then the

View License Data

button in the

Node

tab.

At this point, the required license values for the Composer configuration appear.
Clicking

Check License Data

results in the values being compared to the PAK

codes. If the license is correct, the text

Available

show in the

Available license

column.

Before checking the license, be sure that the MK8000 server is running. You can

start and verify the status of the server tasks with the

System Monitor

icon

in

the bottom right corner of your screen.



For more information, see Appendix A at p. 87.

Fig. 65 Viewing and checking the MK8000 license

«
...
62
63
64
65
66
...
»

Содержание MK8000 MP4.30





























































































Отзывы:

Нет отзывов

Похожие инструкции для MK8000 MP4.30

SuperServer E100-8Q

Бренд: Supermicro Страницы: 48

NSLU2 - Network Storage Link NAS Server

Бренд: Linksys Страницы: 64

Бренд: TYAN Страницы: 170

Бренд: IBM Страницы: 110

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

FusionServer 1288H V5

Бренд: xFusion Digital Technologies Страницы: 96

Бренд: NEC Страницы: 69

Бренд: Acnodes Страницы: 1

Бренд: Acksys Страницы: 24

Бренд: Avaya Страницы: 270

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Kramer Страницы: 28

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

TEW-P1UG - Wireless Print Server

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 15

Бренд: Black Box Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды