Siemens MK8000 MP4.30 Скачать руководство пользователя страница 15

Страница: 15 / 92

Installation

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

Based on the above listed data and information, a data recovery scheme should
be put in place.

Passwords

Keep a copy of the master passwords. The list includes:



Window administration password(s).



The SQL 2000 password, if used (see p.43 and p.11).

Data privacy and protection

As stated in 1.4 at p.7, compliance with local regulations must be addressed.
This can concern paper listings as well as tapes and memory support.

For further information on general security issues regarding Siemens products,
please refer to the internal document

IT security in BT project execution

Содержание MK8000 MP4.30





























































































Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды

Siemens MK8000 MP4.30, Руководство по установке и настройке

Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды