Siemens MK8000 MP4.30 Скачать руководство пользователя страница 25

Страница: 25 / 92

Installation

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

Microsoft .NET V2.0 framework library is a pre-requisite for SQL Express 2005

Installing SQL Express 2005

. Launch the SQL Express 2005 installation from the setup page (Fig. 5).

If necessary, Windows Installer 3.1 (Microsoft code KB893803) is automatically
installed.

. Confirm you accept the license agreement (Fig. 12) and click

Next

Fig. 12 Accepting the SQL Express 2005 License Agreement

. In the preliminary setup windows that appear on the screen, click

Next

then

Install

, and finally

Next

again.

. In the setup wizard that appears (Fig. 13), click

Next

Fig. 13 Microsoft SQL Server Installation Wizard

. The installation procedure performs a configuration check to ensure that

hardware and software requirements are matched.

In the resulting window (Fig. 14), you can find any errors or warnings found (see
the

Status

column). Use the

Filter

command to limit what items are visible in

the list. Follow the

Message

link and read any related information that may indi-

cate if and why your system cannot fully support SQL software.

Содержание MK8000 MP4.30





























































































Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды

Siemens MK8000 MP4.30, Руководство по установке и настройке

Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды