Siemens CP 1243-8 IRC Скачать руководство пользователя страница 51

Страница: 51 / 140

Configuration and operation

4.6 Configuration in STEP 7 V5

CP 1243-8 IRC
Operating Instructions, 06/2015, C79000-G8976-C385-01

●

Connection mode (RS232)
Configuration in the "Interfaces“ tab
–

MSC station
The serial interface is configured as an Ethernet interface. The communication is

handled using the MSC protocol. The proxy is configured to connect to the Internet as

an MSC station via a DSL router.

–

Neutral
The serial WAN interface of the proxy is set to the connection mode "Neutral“ if

communication is handled via a dial-up network or dedicated line.

Figure 4-2

Properties dialog, "Interfaces" tab with WAN interface to which a dial-up network is

connected.

●

Modems for dial-up networks
In addition to the TIM for communication of the CP via dial-up networks, the required TS

modules for the serial WAN interface of the proxy can be selected in theInterfaces tab,

see below.

●

AT strings for TS modules
AT strings were added for the TS modules, see below.

●

No SMS configuration
The configuration of the sending of SMS messages is not possible for the proxy in

STEP 7.
You can arrange for the sending of SMS messages in STEP 7 Basic for every data point.

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды