Siemens CP 1243-8 IRC Скачать руководство пользователя страница 14

Страница: 14 / 140

Application and properties

1.2 Communications services

CP 1243-8 IRC

Operating Instructions, 06/2015, C79000-G8976-C385-01

Supported network node types
The CP with the firmware version described here (refer to the Preface) supports the network

node type "Station".
Depending on the transmission protocol being used, one of the following transfer modes can

be configured in STEP 7 V5.

●

GPRS station

●

MSC station

●

Neutral

S7 communication and PG/OP communication

Reading / writing data from / to a CPU via the mobile wireless network is possible if S7

communication is enabled in the configuration of the CP.
The following instructions are supported:

●

PUT/GET
The CP supports these program blocks as client and server for data exchange with

remote stations (S7-300/400/1200/1500)

●

PG functions

●

Operator control and monitoring functions (HMI)

You will find details on the program blocks in the information system of STEP 7 Basic.
For S7 communication, the CP requires a fixed IP address.

Communication via Open User Communication (OUC)

Via the Ethernet interface of the CP and the program blocks of the Open User

Communication on the CPU the CP has the following communication options:

●

Communication with SIMATIC stations via S7 connections

●

Sending e-mails
In contrast to the corresponding service of telecontrol communication (see above), to

transfer e-mails via OUC, program blocks TMAIL_C need to be used, see section

Programming the program blocks (OUC) (Page 97).

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды